trinituner.com

647 spend the money and buy some original parts if you can, if you do you would not have to change parts for the next few years...

647 wrote:Did a suspension check and a number if issues came up:
1. burst ball joint and big bushing
2. Velocity joints bad
3. rack ends need to change

WTK, has any one ever bought a compete axle with CV joints Foreign Used? are they any good?

its a hit or miss with those...

Started buying one by one item, kinda short on funds right now...i did some calling around and i getting an entire cradle arm with the ball joint and bushings for $250.00 new, but i have used subtitute bushings before and they only lasted a few months (i got lowering springs on my car) so i not to sure if to purchase this...

@$250, you can be almost sure you'll have to replace again in a few months.

If you that short on cash, a very carefully chosen FU may be a better option.

I've seen FU cradles last years and some last weeks so it is a risk, but, then again, so is cheap chinese stuff.

Thanks dude, i think i will look around for good FU cradle arm, them subs dont last. There is a place in marabella called Daily Imports, their prices are really good on mazda parts..they then to have all the parts i am looking for.

Where Daily Imports located?

When you reach Marabella round about, turn unto the road that leeds to Mani Ramjohn stadium, they are located just before the Heath center.....i will pass and get a contact # for them so that people could call and find out what they got.

I'll add that to our thread for mazda selers.

Daily Imports # 658-3873/488-1282/301-4878

Hey i jacked up my car today to paint brakes shoes and noticed that my front right side brake pads have a lot more wear on it than my left front side pades. I have no major breaking problems except when going over the hills of Maracas when i reach down by the beach i find it tends to be very soft and i have to mash right down to get even the slightest breaking power. What do guys think can cause this and will cause problems for me in the long run?

Faiz had BJ cradles for $800, the guy said it's Japanese and really good, that's $1600 a pair. Anyone knows Southern sales price?

My brakes does that same thing going Maracas, some guys using stoptech disc pads (I don't know when they'll bring in for retail) Maztune had a pair of slotted rotors which will help your disc pads keep cool for the Maracas run. Adjust your brake shoes so all the strain don't go to the disc pad. The piston probably stick, so you should do a service, flush out your old brakes fluid too (I bet it boiled going Maracas). Does the brakes fluid look darkish?

Save up to do a four wheel (5 hole) disc brake conversion (easier said than done, I was saving for this & something always coming up), invest in good disc pads & slotted or drilled rotors (not drilled & slotted together)

Thanks Groovemaster, i will check Faiz and Also try to get a price from Southern Sales ( but i find that SS never have anything and its always on the next shipment)....gona get my brakes serviced today once i can run away from work...and no the brakes fluid is the normal color

All cross drilled for the BJ tend to crack I have seen so far, I will stick to the slotted.

Info added to thread. Thank you 647.

naresheep, my ebc rotors are blind drilled, aka drilled halfway through...no cracks

Driving my car today on the highway at 60kph (morning traffic) and my car/steering just started to vibrate and car started to pull the left. I pulled aside and locked my steering to the right and then the left, did this twice and then contined to drive...vibration on the steering stopped and alignment was good now.....what ould have caused this?

bad road surface will sometimes cause 'tracking' if tyres are worn unevenly.

tyres are only two months old have dont have any uneven wear on them...will a bad tie rod end cause this? how do you tell if its bad?

tie rod end? steering end? its possible, you'd have to disconnect it and check for excessive play/movement. consider that it is a ball and socket joint so you will know what kind of movement to expect.

Thanks, will do some checks over the weekend

hey can i replace the transmission on the car or i need to remove the entire engine ...its a 323bj

Tranny can drop out independent of the engine.

hi i have a 2002 mazda protege which says incorrect gear ratio p0730 help please!!! it starting giving me this code suddenly no warning signs etc the gears were not slipping or anything just one night while i was driving i felt the tranny downshift and upshift abnormally it was like the car was confused as to which gear to select!!
things i tried so far: flush out old tranny fluid was using redline d4, fluid was nasty btw. changed the filter under the valve body and put in fresh redline d4 around 3 and a half quarts anyways can anyone assist me with this problem thanks

Hey folks, i'm new on the forum. I'm looking for a zm12 brainbox for my mazda 323 bj 2000. the one with two lights to the front, the older one nuh. My car is down for 2 months and dem fellas in de bamboo lying and saying ohh they getting it and all that.. but they jus on rel games dread. Anyone know if you can use another brainbox instead like a ZL or a zm16, or are there negative effects from that? Or if anyone has a ZM12 on sal u can link me please.. Stephen - contact : turst9@hotmail.com

protege9 what engine does your car have?

Ok i checked the resistance between the terminals of the input speedsensor got 362 and according to the manual it should be between 250 and 600 ohms anyways what else can i try?

my engine i think is a 1.6 and it's the bj mazda 323 hatchback. the brainbox i'm looking for , or had in my car is ZM12 18 88 1A

Fixed the tranny problem people!!! thanks

how? 

hi guys new to this forum i own a 323 f bh local and i am having two problem with my car one is rear suspension when there is one ore more people in the back i hear a banging song from the back i checked a mechanic he said shocks i bought foreign used assembly same thing carry it back got new brand shocks and spring andis the same thing next problem is my tranni in think it is stuck in third gear carried it by a tranni guy he said seloniod we changed it and still same thing any one has any ideas

isalee26 wrote:hi guys new to this forum i own a 323 f bh local and i am having two problem with my car one is rear suspension when there is one ore more people in the back i hear a banging song from the back i checked a mechanic he said shocks i bought foreign used assembly same thing carry it back got new brand shocks and spring andis the same thing next problem is my tranni in think it is stuck in third gear carried it by a tranni guy he said seloniod we changed it and still same thing any one has any ideas

check the shock mounts in the rear for the banging
tranny may need to get a diff person to look at