??? still hoping on this project , whats up these days

_________________
Belittles FugiTECH he is THE SR20 Specialist that cant even change an Alternator Belt..Calls back a month later with a Technical Question> Sad

i pass almost every evening and gape...this car is sweet!

_________________
他不理解英语

Wuht ??

_________________
meh bonnet cyah close

_________________

d firetruck!

_________________
I'm so JDM i sleep on the right hand side of my bed...

hehehehehehe...

project still on the cards...just other priorities these days....I shud move this until its back on the road though.....

_________________
...You like a SAGHS virgin tryin to explain the finer points of buttsecks...

[stones]I shud move this until its back on the flatbed though.....[/stones]

_________________

so the project is back full swing.

Bit of an update/recap. As yall know the engine went PANG! on the dyno on its way to 200whp....we got some way and then had to rebuild. That was over a year ago...other priorities took precedence, but now (due to an irritant buyer...lol...sorry Gregory) its back. What we've done so far:

Took the head to Precision Heads (Rado) to so some extensive head work. Have to admit, Rado is one cool cat who didnt know I was Banzai until after the fact..lol....and he himself has a major project that will put alot of cars in question/check...good luck with that.

We got CP pistons. Remember before we went on the stock SR16 pistons which didnt last long under the 13:1 compression. Took it to Baldwin to do the Bore and Deck of the block as well as skim the head.

Got the Jim Wolf Cam Gears (shut up W2J...lol) and once the head and block work is done, we'll mount up and see. Also installing the AEM Water?meth kit and POSSIBLE get the Excessive Technologies Intake Manifold.

I sold the Sr16 ECU and opted to go with the SR20Ve Ecu with the E-Manage Ultimate piggy back.

What else. Brakes wise. We again chagned up. I had sold the last Brembo brakes. I got another pair adn we are pairing it with some WIlwood hat and disc combinations (300/330mm) in the front. I'm using EK rear slotted discs for the back.

EXtractor wise. We're doing a custom tri Y setup that we're copying from the Hondas. Jimmy from the east is currently doing that work. Entire system will be 3 inch through out now.

There are other cosmetic stuff that we have in store but as we go i"ll update.

_________________
...You like a SAGHS virgin tryin to explain the finer points of buttsecks...

only update pic i have for now.....



The DC5 calipers bolted Right up...no issues...but u cant use the rotor discs due to the deep hat offset. Hence going with the Wilwood combination. If anyone knows of a honda or nissan big brake rotor (4 hole) that has a .56 offset on the hat (measured from the mid hieght of the hat on the spindle) let me know....

_________________
...You like a SAGHS virgin tryin to explain the finer points of buttsecks...

them rims............... when can the collective pee on it?
yes.......... that is the state you reach.

_________________

nice glad to see this project back on track

_________________
cruising sfl

Still a Na Fan , cant wait for good power and 1/4 mile results

_________________
Belittles FugiTECH he is THE SR20 Specialist that cant even change an Alternator Belt..Calls back a month later with a Technical Question> Sad

^^ i eh know bout teh 1.4 mile part..but the numbers should be interesting....

_________________
...You like a SAGHS virgin tryin to explain the finer points of buttsecks...

nice.....i gape at this car almost every evening on a weekday as i head home.....lovely

_________________
他不理解英语

it's about damn time metro

_________________
where's Perry?

Are you still shooting for 13:1 compression with the new pistons?
If going that high of compression, why are you using a piggy back? At that point I would opt for full standalone.
I bet I missed it somewhere, but what cams are you going to use for that much compression?

Nice build btw.

_________________

_________________
If it don't make dollars, it don't make sense.

Suhweeeet...

_________________
S-Chassis Trinbago Facebook Group

Local blog MotorEdge™

Rastaman da thread title eh soundin too good eh.

I doh tink Rado would appreciate it.

_________________
If it don't make dollars, it don't make sense.

lolol...thais urs or minez? does cyar tell the difference nuh...

well Block bored n decked (as in Yakusa's photo) and Baldwin also skimmed the head and torqued it down.

So its to flip it and "stick it" the pistons now.... I real busy these days so i cant be at the shop to take pics but when I can I will...

_________________
...You like a SAGHS virgin tryin to explain the finer points of buttsecks...

Just making sure, Baldwin use da torque plate when boring the block? When last I spoke with them he didn't mention the torque plate andwhen I inquired he said that the person will have to walk with their plate as they don't provide one, I was like wha??? Not sure if this has changed since last I checked.

_________________
Jason - 494-4975
Resident DIY'er - Why Pay Someone to Learn on Your Car When You Can Do It Yourself???

Same thing I was now going to ask TriniGT.. I real skeptical with that machine shop in the East

_________________
meh bonnet cyah close

is no scene yakuza.


I was looking out for some "head" pics......

_________________
737 4882

you are correct. Baldwin does not use a torque plate unless you provide one. I had to rent one from another engine builder for the process.


Thing is, from listening to him (Baldwin) you realize that he has a wealth of knowledge, but like everyone else in this place..they think they know it all and try to "school le old man" on what should be done. So his position is this: you want something done? you did the research and sure it can be done? then come through.

To each his own.

_________________
...You like a SAGHS virgin tryin to explain the finer points of buttsecks...

So ah could really put a K20 head on an SR block den! Nice

_________________
meh bonnet cyah close

cleaned out the engine bay today...of the excess wiring and degreased it....going for round two tomorrow. Wilwood brakes have left Le USA and on it's way here...looking forward to seeing the eventual hook up with that.

Need a solid upholsterer to do some custom work for me....but east-west based...not flatbedding the car too far from home..

_________________
...You like a SAGHS virgin tryin to explain the finer points of buttsecks...

there is a guy i went by he located in the back of medical associates in st.joseph (i cant remember the exact street) but im sure someone up there knows him. A muslim guy i believe

_________________

^^ then i know of who you speak. I forgot about him..will check him this week.

_________________
...You like a SAGHS virgin tryin to explain the finer points of buttsecks...

Keep it going Rassey , think i last visited this page quite a few years ago , but thanks for the updates and good luck

Nice lil beast

_________________