Forums

static

Good day, I am trying to find someone who can assist with replacing the rear seal on a isuzu 4BE1 engine. This is the isuzu NPR 3ton truck. This seal replacement requires a specific tool to correctly install the seal. Any links will be appreciated. Hopefully at a reasonable price. Truck is in South....

static

forgot to mention, it is the 4x4 turbo model

static

Good day,

When shifting to 2nd and 3rd i am getting a slight grate. Shifting to 4th and 5th is smooth.

Now if i hold the clutch down and let the rpm drop before shifting the grating is less or none at times.

Anyone has experience with this? and the possible causes/fix?

Thanks in advance.

static

Good day, Any information or advice will be appreciated. I am trying to find out if i need to obtain approval from the Borough Corporation to create a second driveway into my property? The driveway will need to be created over a shallow drain (not box drain) that runs parallel to the house/road simi...

static

I had this problem once and it was the AC leaking.

static

When u took the alternator to be checked did they bench test it? This would prove it is good. Part of the bench testing is the light going off similar to the light on the dash and it becoming hard to turn.

static

Can anyone direct me to a local or online source for front camber kits. I have been looking but no luck so far.

Thanks.

static

This is cvt? Grating sound is not good. Could be a bearing shell out.

static

Those are two magnetic revolution sensors. I have spare ones if u interested.

static

Sounds like the clutch fan is in need of some silicone oil. The fan doesn't spin much on idle and the temp goes up. Doesn't help the AC condenser cool down either.

static

Anyone know who or where sells camber kits for the Sharkmouth Galant?

Local or online?

Any help is appreciated.

Thanks.

static

Hi

Can anyone say if the Roadstone Darkhorse tyre - 235/60/14

can fit on the Galant without issue? The car has the original star rims

Thanks.

static

Good day,

I need to advance the base timing by 15 deg on a local sharkmouth galant. It has the sohc 4g63 engine.

Any one knows how to get this done?

can this be done with a good scanner? (Launch or Autoboss)

thanks.

static

Check fuel pressure.

static

Had a problem where the AC was pulling down the idle. Turned out to be a faulty condenser. The pressure on the high side was above 300. The compressor was harder to turn so it loaded the engine a lot more.

static

Very good question. Wanted to know that too.

static

OK so two other things that can cause that.
Bottom rad hose sucking in or water pump fins damage and not pushing the water

static

May be a dumb question but you saw d rad fan on? Sounds like that fan not working.

static

Check this properly b4 u spend any money. To check for the bubbles properly take a small water bottle (blue waters) for Eg fill it with water take off d rad cap and turn d bottle upside down in d rad. Secure it so it won't fall off. Start d engine and look for bubbles in d bottle. I had an issue wit...

static

Anyone did the modification on a Box Lancer gas tank to use an internal fuel pump? Just wanted to know the best way to do it.

Don't want to mess with the fuel gauge and that's the only access point from inside the trunk.

Thanks.

static

Thanks for the link, that engine seems to have a fuel rail and 4 injectors, nice conversion if the intake manifold etc was available here.

static

Just wanted to know if anyone has knowledge or experience with any engine management system that had good results on an original stock Sirius 1800 turbo?

Researching this but not coming up with much.

Thanks.

static

Reminds me of when i decided to do ah little 'upgrade'..... before i knew it it had hit the 20K mark and going!
Thoroughly enjoyed it though...

static

kit with clutches and steel plates - $1820 (customs and shipping $700+)
second kit - $650
Torque converter repair - $850
7 quarts of oil @ $60

$3740

static

so i ordered the kit (seal kit, filter, clutches and steel plates) and did the rebuild myself.

With the original SiR tranny, you need to buy two kits to get all the parts you need. The CRV tranny that some guys use in SiR uses only one kit.

So far the tranny is working perfectly.

static

ZIM, thanks.

I have been able to establish that the same brand available online (transtec) is also sold by the Auto Supplies ppl in Chag. so i can assume the quality is the same.

I have also seen three kits - Master kit, Banner Kit and overhaul kit

static

Just wanted to know if anyone bought a rebuild kit online that was good quality and the link.

Any feedback would be appreciated.

static

trendy kids in POS, upstairs Shoppers freezone in Chaguanas, Bell Air stores in marabella...

static

so does anybody have an inexpensive scan tool that works with D22 frontier or other Japanese vehicles?

Auto Boss and Launch are really not within my budget for a home use device.

static

i have seen this with a 4g15 carb engine that i did some work on. so i took a chance with a fix that i'm sure other ppl wont bother to try. I took the crank pulley and gear to a machine shop, got it drilled and tap to use two 12mm bolt. i bolted the gear to the pulley so that there will be no 'play'...