Yeah, i will try a new blade and troubleshoot from there, possibly one of those 3 point ones. It's a Makita 36v brush-cutter so the typical gear housing actually houses the electric motor. Only thing at the head that might cause vibration is the bearing, but I'm not getting any type of play when i s...
Bumped my brush blade on some old iron hidden in the grass, now its out of balance causing the wacker to vibrating badly. Tried for the last 3 days to grind/balance it on a nail but no luck, not sure if the nail setup will work for this type of blade actually. Is there anywhere that re-balances thes...
Looking for a replacement pressure regulator valve for a Makita MAC2400, mine is leaking from the regulator knob. Any idea where i can source one locally?
Guys, do your local user manual state this under the recommended fluids and lubricants section or does it just have the API grade listed (as in Page 1 of this thread)? Diesel engine oil : API grade CF-4, JAS0 DH-1 Reason I'm asking, according to the JASO Engine Oil Standards, the oil I'm running now...
Rear engine seal most likely. yea could be the engine seal . my advice ..if u replace . install new clutch one time .. cause that is as lot of work n it easier to install with engine out Thanks guys. Is it in anyway unusual that the NAV is doing 53k and the seal is gone or is that within "acce...
Rear engine seal most likely. yea could be the engine seal . my advice ..if u replace . install new clutch one time .. cause that is as lot of work n it easier to install with engine out Thanks guys. Is it in anyway unusual that the NAV is doing 53k and the seal is gone or is that within "acce...
Afternoon Guys, has anyone experienced or know what might cause an engine oil leak from this area (green arrow). Appears to be between the Engine and Trans. Any assistance/advice would be very much appreciated. Its a manual 6 speed btw.
Had the 'Sports Version" emblem removed from my van after getting the tailgate re-painted. ABW said it was rubber and it got damaged when they were taking it off.
Long shot, but does anyone know where i can get that emblem?
Navara bed 1/2 inch lower on drivers side. Van was bought 2 weeks ago. Measured it with a full tank and low tank of fuel Is that normal? Anyone noticed this with theirs? Thanks Check ur body mount rubbers, and see if any cracked or missing. Thanks LH, checked both sides and they are intact, look al...
So i went by REO Auto in EL Socorro to have the OEM Alarm upgrade done to the NAV. They used the Automate AM 1.5 alarm system. Cost $1200. The fact that the OEM Alarm Upgrade used is US$50 - 60 online doesn't bother me as much as below. While going thru the alarm features, the guy told me he cannot ...
In terms of security, the van comes with an immobilizer and alarm (Stock), the alarm only goes off when its armed and a door is opened, it does not have a shock sensor to detect vibrations, kick, etc. I would like to add a shock sensor but more importantly i want to keep using my existing van remote...
Thanks kerwinishere/tr1ad, i'm not going to worry about it esp if vents/etc are possibly involved, usually its on face all the time and that's generally fine, was only thinking if the front windscreen gets frosted up and i had to run the defogger on the front, which it doesn't seem to have a setting...
Hi All, Saw my import Navara last week and couldnt help but notice the AC Air Flow Controls (Knob on right) were a bit different. This is the one i have in my van. AC Controls 1.jpg This is the one taken of one the vans at the office from Massy AC Controls 2.jpg And this is similar to the newer van ...
Hi, Can anyone point me in the direction of someone/firm that does the Rhino Spray-on Bedliners? Found both Hydrocarb and Ziebart on the forums but no luck. Hydrocarb does not do vehicles anymore and Ziebart does not have the materials in stock, no date on when they will be getting. Any assistance w...
better to make your own, just buy the insert plate or even make that too if you are good with a router. Use a piece of laminate flooring for the plate. What he said ^^^ there lots of YouTube videos on how to do it Contemplated building initially, still an option overall but wanted to see if there w...
nice deal! looks solid http://www.amazon.com/gp/product/B004L9 ... d_i=507846 Hi, Purchased this kit in mid-2012, used it extensively and still going strong. I had Cariszone bring it in for me. You can check the price in the link, may need to be revised though, since then http://www.cariszone.com/c...
So went to check out one of the South New Cars Dealers on Sat. Saw a Nissan Navara Sports Edition covered with every imaginable piece of decoration you can have. Guy said around about 260-265k for it stock "no deco" and "manual". Leaning towards that purchase. What do you guys t...
So went to check out one of the South New Cars Dealers on Sat. Saw a Nissan Navara Sports Edition covered with every imaginable piece of decoration you can have. Guy said around about 260-265k for it stock "no deco" and "manual". Leaning towards that purchase. What do you guys th...
Going to call Maska in the morning, hopefully they bringing in manual Navs (face-lift). not a fan of all the frills that come on the van though, but maybe some of it can come off. Prefer the stock look.. M.Rampersad only bringing in automatic and they are out of stock until May, they said. I'm even ...