TriniTuner.com  |  Latest Event:  

Forums

Search found 647 matches

by blazing
June 27th, 2011, 12:14 pm
Forum: MITSUBISHI
Topic: The Official CS Lancer Thread!
Replies: 14576
Views: 871839

Re: CS Lancer!

i usually experiment with stuff and have no clue where it ends up. Like my neo rb25det, everyone i asked, said it will be destroyed over 350hp....Im doing 370rwhp and i use the car everyday. Research shows its still an rb25det that can make power to about 550, safely 500. For real dude sometimes ur...
by blazing
June 4th, 2011, 7:09 pm
Forum: MITSUBISHI
Topic: Brake Upgrades for CK Mivec?
Replies: 92
Views: 11371

Re: Re:

I was just wondering if I would need another banjo bolt to connect my current brakeline to the Galant (Single Big Piston) caliper that I have. The Galant Caliper has a screw in type line. Is this bolt on? i used a screw type caliper with banjo bolt already. it needed 2 washers as the banjo was slig...
by blazing
June 4th, 2011, 7:00 pm
Forum: MITSUBISHI
Topic: The Official CS Lancer Thread!
Replies: 14576
Views: 871839

Re: CS Lancer!

Automotive supply company - Charles St, POS

Thas on the same road by Diamond, has a 3M sign outside.

I find their parts are quality and cheap considering.
by blazing
June 3rd, 2011, 3:33 pm
Forum: MITSUBISHI
Topic: The Official CS Lancer Thread!
Replies: 14576
Views: 871839

Re: CS Lancer!

Came across the following prices and parts for 4g18 in POS:

1) Gates 109T x 25mm Timing belt - $122
2) Gates Water pump - $240
3) Crankshaft seal - $28
4) Crankshaft seal - $40
5) Tappet pan gasket/spark plug seal kit - $108.68
by blazing
November 20th, 2010, 1:57 am
Forum: MITSUBISHI
Topic: Handbrake Light Problem
Replies: 13
Views: 744

Re: Handbrake Light Problem

take off the brake cover and push the rubber back into the cap....
by blazing
November 7th, 2010, 12:50 pm
Forum: MITSUBISHI
Topic: FTO to CK swap...can it work?
Replies: 25
Views: 1808

Re: FTO to CK swap...can it work?

trinibuggy wrote:FTO tranny will work with a 4G63t(evo 3)?



no
by blazing
October 24th, 2010, 10:08 pm
Forum: MITSUBISHI
Topic: FTO to CK swap...can it work?
Replies: 25
Views: 1808

Re: FTO to CK swap...can it work?

1.8 gs fto engine...works exact in d ck lancer just wire up and drive,only modification is d axels for d fto engine is longer by 2mm(it will still work but when u turning corners u will hear a rubbing noise),so u have to use back d ck axels. SCHOLARS is right 4g93t smaller and faster than v6..........
by blazing
October 22nd, 2010, 1:37 am
Forum: MITSUBISHI
Topic: FTO to CK swap...can it work?
Replies: 25
Views: 1808

Re: FTO to CK swap...can it work?

chindian88 wrote:
:shock: where can i get the V6?


may have a v6 and 5spd tip trans for sale in a few..
by blazing
October 15th, 2010, 1:15 pm
Forum: MITSUBISHI
Topic: FTO to CK swap...can it work?
Replies: 25
Views: 1808

Re: FTO to CK swap...can it work?

certain parts will work and are easily aailable, others are a pain.
by blazing
July 27th, 2010, 3:55 pm
Forum: MITSUBISHI
Topic: WTK water pump in ck gone bad
Replies: 3
Views: 462

Re: WTK water pump in ck gone bad

bess to get timing belt and tensioner one time
by blazing
July 4th, 2010, 1:46 pm
Forum: MITSUBISHI
Topic: mitsubishi eclipse parts -- brake pads
Replies: 1
Views: 405

Re: mitsubishi eclipse parts -- brake pads

Sounds like u need Hawk HPS
by blazing
January 12th, 2010, 7:40 pm
Forum: MITSUBISHI
Topic: **CK4 Back door stuck shut
Replies: 11
Views: 1128

i opened a galant with the same prob.

once you strip off the upholstery, follow the line until you reach the lever and pry down on the lever..it'll pop open hopefully.
by blazing
December 23rd, 2009, 1:49 am
Forum: MITSUBISHI
Topic: CK2 Grounding Points or Good Electrician?
Replies: 5
Views: 1038

Image
by blazing
December 16th, 2009, 11:42 pm
Forum: MITSUBISHI
Topic: The Official CS Lancer Thread!
Replies: 14576
Views: 871839

idlemind wrote:now if only the rotors from those said vehicles would work


4x114 rotors from the 93 VR4 or EVO 1-3 Rotors would work with some drilling.
by blazing
December 16th, 2009, 6:14 pm
Forum: MITSUBISHI
Topic: The Official CS Lancer Thread!
Replies: 14576
Views: 871839

Well good news for you CS guys, I just fitted the Eclipse twin pot caliper and bracket that I had on a CK Lancer on a CS. So this means that the 1G Eclipse,2G Eclipse, Evo1-4, VR4, Stealth, Diamante, Mirage, CK Lancer all have the same spacing for the brackets and any caliper/bracket should just bol...
by blazing
November 27th, 2009, 11:10 am
Forum: MITSUBISHI
Topic: CM2A Air Bag installation
Replies: 2
Views: 598

Do not reconnect. You will have to clear the SRS code and check all sensors first

Is the SRS light on the dash on?
by blazing
November 27th, 2009, 11:08 am
Forum: MITSUBISHI
Topic: some mirage qustions
Replies: 3
Views: 653

4x114
by blazing
November 24th, 2009, 12:05 am
Forum: MITSUBISHI
Topic: So yuh went by DM!
Replies: 20
Views: 2120

I made the mistake of going by DM North since I had no time (or energy) to bleed brakes and change all 4 disc brakes. This was when the $600 service special was ongoing so i took that one time. On receipt of the bill they charged me more than the special rate, since my car was not a lancer, then par...
by blazing
October 31st, 2009, 1:50 am
Forum: MITSUBISHI
Topic: Mivec / Galant Brakes Pad
Replies: 23
Views: 1525

Hawk HPS if you can get
by blazing
October 28th, 2009, 11:42 pm
Forum: MITSUBISHI
Topic: WTK:CS3 rear disc options
Replies: 42
Views: 2679

ok where are the 2 lines on the bottom of the MC running to?
by blazing
October 26th, 2009, 7:50 pm
Forum: MITSUBISHI
Topic: WTK:CS3 rear disc options
Replies: 42
Views: 2679

ABS and non ABS both have 2 ports
by blazing
October 26th, 2009, 7:29 pm
Forum: MITSUBISHI
Topic: WTK:CS3 rear disc options
Replies: 42
Views: 2679

I wonder whas d wheel spacing on that ralliart setup 5 x 100 or 5 x 114.3?! That question, nes123 bum rush meh post. And I thought was Trinidad Brakes, Clutches and Hose apparently. Didnt know there was a Trinidad Hose. But if its Goodridge they selling then I would jus bring them in myself. Il che...
by blazing
October 26th, 2009, 7:25 pm
Forum: MITSUBISHI
Topic: WTK:CS3 rear disc options
Replies: 42
Views: 2679

turbo_beast369 wrote:
even if I get a CS5 ralliart master cylinder I cant use it becuz of non ABS....



An ABS master cylinder will work, and will be bigger than your non-ABS one.
Only difference is the bore.
by blazing
October 25th, 2009, 2:16 am
Forum: MITSUBISHI
Topic: WTK:CS3 rear disc options
Replies: 42
Views: 2679

fto is 5x114
by blazing
October 9th, 2009, 10:52 am
Forum: MITSUBISHI
Topic: mirage booster upgrade
Replies: 5
Views: 717

I have 2 of them.

One came from the VR4 AWD with ABS and the other from an Eclipse AWD GSX with ABS.

Both bolt right up.
by blazing
October 7th, 2009, 10:59 am
Forum: MITSUBISHI
Topic: mirage booster upgrade
Replies: 5
Views: 717

get a double diaphram booster from an ABS equipped lancer.

Normally has a 1 1/16 bore MC as well
by blazing
August 27th, 2009, 9:32 am
Forum: MITSUBISHI
Topic: Replacement for 4G63
Replies: 23
Views: 2170

4g63t

:lol:
by blazing
August 27th, 2009, 9:26 am
Forum: MITSUBISHI
Topic: 4G18 sohc to dohc
Replies: 31
Views: 14706

financially it will not make sense, just like turboing the 4g15 wouldnt.. but thats the price of being unique and learning on your own.

I had a spare 4g15 on the ground and was getting a block from the 4g18 free. The costly part would be the vitara pistons i was looking for and forged rods. :lol:
by blazing
August 25th, 2009, 11:29 pm
Forum: MITSUBISHI
Topic: 4G18 sohc to dohc
Replies: 31
Views: 14706

SCHOLARS wrote:y u want to put that crank in?????


stroke is different 82.0mm to 87.3 mm.
would need to check clearance though. just a project i was going to attempt. 4g18 piston is also slightly bigger by 0.5mm.

*KRONIK* wrote:hows "DAT" coming along??


Slow and expensive..
by blazing
August 24th, 2009, 10:31 am
Forum: MITSUBISHI
Topic: 4G18 sohc to dohc
Replies: 31
Views: 14706

i was going to truy putting the 4g18 crank in the 4g15... moved on now though

Go to advanced search