Forums

blazing

i usually experiment with stuff and have no clue where it ends up. Like my neo rb25det, everyone i asked, said it will be destroyed over 350hp....Im doing 370rwhp and i use the car everyday. Research shows its still an rb25det that can make power to about 550, safely 500. For real dude sometimes ur...

blazing

I was just wondering if I would need another banjo bolt to connect my current brakeline to the Galant (Single Big Piston) caliper that I have. The Galant Caliper has a screw in type line. Is this bolt on? i used a screw type caliper with banjo bolt already. it needed 2 washers as the banjo was slig...

blazing

Automotive supply company - Charles St, POS

Thas on the same road by Diamond, has a 3M sign outside.

I find their parts are quality and cheap considering.

blazing

Came across the following prices and parts for 4g18 in POS:

1) Gates 109T x 25mm Timing belt - $122
2) Gates Water pump - $240
3) Crankshaft seal - $28
4) Crankshaft seal - $40
5) Tappet pan gasket/spark plug seal kit - $108.68

blazing

take off the brake cover and push the rubber back into the cap....

blazing

trinibuggy wrote:FTO tranny will work with a 4G63t(evo 3)?

no

blazing

1.8 gs fto engine...works exact in d ck lancer just wire up and drive,only modification is d axels for d fto engine is longer by 2mm(it will still work but when u turning corners u will hear a rubbing noise),so u have to use back d ck axels. SCHOLARS is right 4g93t smaller and faster than v6..........

blazing

chindian88 wrote:
where can i get the V6?

may have a v6 and 5spd tip trans for sale in a few..

blazing

certain parts will work and are easily aailable, others are a pain.

blazing

bess to get timing belt and tensioner one time

blazing

Sounds like u need Hawk HPS

blazing

i opened a galant with the same prob.

once you strip off the upholstery, follow the line until you reach the lever and pry down on the lever..it'll pop open hopefully.

blazing

blazing

idlemind wrote:now if only the rotors from those said vehicles would work

4x114 rotors from the 93 VR4 or EVO 1-3 Rotors would work with some drilling.

blazing

Well good news for you CS guys, I just fitted the Eclipse twin pot caliper and bracket that I had on a CK Lancer on a CS. So this means that the 1G Eclipse,2G Eclipse, Evo1-4, VR4, Stealth, Diamante, Mirage, CK Lancer all have the same spacing for the brackets and any caliper/bracket should just bol...

blazing

Do not reconnect. You will have to clear the SRS code and check all sensors first

Is the SRS light on the dash on?

blazing

4x114

blazing

I made the mistake of going by DM North since I had no time (or energy) to bleed brakes and change all 4 disc brakes. This was when the $600 service special was ongoing so i took that one time. On receipt of the bill they charged me more than the special rate, since my car was not a lancer, then par...

blazing

Hawk HPS if you can get

blazing

ok where are the 2 lines on the bottom of the MC running to?

blazing

ABS and non ABS both have 2 ports

blazing

I wonder whas d wheel spacing on that ralliart setup 5 x 100 or 5 x 114.3?! That question, nes123 bum rush meh post. And I thought was Trinidad Brakes, Clutches and Hose apparently. Didnt know there was a Trinidad Hose. But if its Goodridge they selling then I would jus bring them in myself. Il che...

blazing

turbo_beast369 wrote:
even if I get a CS5 ralliart master cylinder I cant use it becuz of non ABS....

An ABS master cylinder will work, and will be bigger than your non-ABS one.
Only difference is the bore.

blazing

fto is 5x114

blazing

I have 2 of them.

One came from the VR4 AWD with ABS and the other from an Eclipse AWD GSX with ABS.

Both bolt right up.

blazing

get a double diaphram booster from an ABS equipped lancer.

Normally has a 1 1/16 bore MC as well

blazing

4g63t

blazing

financially it will not make sense, just like turboing the 4g15 wouldnt.. but thats the price of being unique and learning on your own.

I had a spare 4g15 on the ground and was getting a block from the 4g18 free. The costly part would be the vitara pistons i was looking for and forged rods.

blazing

SCHOLARS wrote:y u want to put that crank in?????

stroke is different 82.0mm to 87.3 mm.
would need to check clearance though. just a project i was going to attempt. 4g18 piston is also slightly bigger by 0.5mm.