Forums

adnj

bought 48 of the m6 rawl bolts today at allied need to get a 1/2" bit for my hilti sds max but they not cheap might be time to buy one of them sds plus hammer drills everybody using now, bits for them cheapish There is an adapter for SDS Max to Plus. A less expensive, lighter weight, corded SD...

adnj

You are going to be very hard pressed to find a headlamp that is less than five years old that is anything other than a non-replaceable LED. The majority will also be Li-ion powered at 3.6 to 9.0 volts. thanks anyway,really looking for a headlight alone because i have a 6v rechargable battery i wan...

adnj

what size expansion rawl bolts would be recommended for 50lb TV hung of concrete block wall ? M6 or M8 and depth ? Rawl specs the safe working load at 3.3 kN (about 330 kg) for M6 and 4.8 kN (about 480 kg) for M8 in concrete block. The failure load is three times that. I would use 4 M6 for double r...

adnj

You should be able to guarantee that there are no metal shavings in the oil pan. The only way is to remove and reinstall the oil pan.

As stated above, consider buying a new oil pan. It will be an easier and faster repair if the part is readily available.

adnj

Bumping this ched for some info/assistance... I have my plans for a garage at approximately 18ft wide, is it possible to get one garage door with that width or do I need two?? Also, if I get a door that width, how wide should the garage be? Exactly 18? More than or less than 18?? Thanks A double ga...

adnj

Ah was studyin to get ah dewalt or makita impact gun but then i see online da ah air tool far more versatile. sooo allyuh fellas know real ting here wa allyuh tink go b d best buy compressor for a small home and unda mango tree hobby mechanic based on experience with past-purchases. Primary uses go...

adnj

You are going to be very hard pressed to find a headlamp that is less than five years old that is anything other than a non-replaceable LED.

The majority will also be Li-ion powered at 3.6 to 9.0 volts.

adnj

Suphur? Maybe. More likely that the contaminant is sludge, microbes, rust, or water.

adnj

Or just walk away.

adnj

The powers of sale and of distress... ...be conferred upon and be exercisable by the mortgagee without any restriction... ...whenever there shall be any other breach or non-observance of ant of the covenants conditions provisions or agreements herein contained. Taken from a random old TTMF deed i w...

adnj

Kronik wrote:Well you would need to give a size to start with. And the type of soil you have also affects that cost as it would determine how deep they have to go and that would affect labor and concrete costs.
And how much of the foundation are you talking about, slab, columns, beam and decking?

+1

adnj

what does reducing the gap do? It reduces the amount of power required to activate the spark plug to burn CNG and eliminate the misfiring that causes the and jerking. I have cng for the past 2 years and works excellent. I agree with what you're saying but tuning the spark plug is common for every I...

adnj

Yes for a brad nailer, but liking your suggestions. Where locally and what brand would you recommend?. Buy from a reputable shop that's close to you. It sounds as if you will be a casual user so any single-stage pancake compressor from a fairly well-known brand like Porter-Cable, Bostich, Campbell-...

adnj

Looking for an air compressor to use a nailer. Price and locations? Assuming that you mean a brad or finish nailer, you can use a small, pancake or torpedo unit with a 2.0 CFM capacity single-stage compressor. If you don't need portability or if plan to build furniture or if you want to run garage ...

adnj

Rovin wrote:so i tort d brand name was INCCO , decided to google - its actually iNG-CO

as i expected : chinese mass produced bisnis .... http://www.ingcotools.com/aboutbrand.aspx

There's also INCO (Interchem Trinidad) but I doubt that those ladders are manufactured locally either.

adnj

There are many light(er) weight fiberglass ladders. Because they are nonconductive, electricians prefer them. That alone puts them in the realm of commercial use. Compared to fiberglass, an aluminum ladder of the same duty rating is lighter in weight, more rigid, impervious to UV damage, and less li...

adnj

fokhan_96 wrote:^^^Good info. Didn't know the weight corresponded to its use. Makes sense now. Always wondered why someone 300lbs would go up a ladder [emoji848]

I've seen it happen.

adnj

I saw that car at an auto show. The Mustang wasn't so impressive in and ofitself but the fact that it was in the movie, was part of one of the best car chases in film historynand was Steve McQueen's car after the movie, was very interesting.

adnj

Fellas any recommendations on a good multi-ladder? I wanted something I can just throw in the wagon instead of using the roof rack. There are some places carrying the Inco 16ft for around $ 1100.00. The thing is the steps looking real thin compared to the regular step ladders and the locking mechan...

adnj

Sundar wrote:even easier test, cut your fingernails/toenails/hair before a full moon and record the amount of time before you cut it again. then repeat this post full moon.

Not too many folks on Tuner cutting their fingernails based on the photos that I've seen.

adnj

Don't be "those guys" and just change your bulb in a reflector housing and then blind oncoming traffic with a bright white glare that basically doesn't help you anymore than stock halogens because of the diffusion. Go get a proper retrofit done....check Triniretrofit on Facebook for some ...

adnj

Milwaukee Torch Nitrus Carbide Reciprocating Saw Blades Milwaukee Tool has announced a new recip saw blade release that’s scheduled for March this year. Engineered to cut up to three times longer than your standard carbide teeth blades, the Milwaukee Torch Nitrus Carbide Reciprocating Saw Blades sho...

adnj

rspann wrote:Yesterday I saw JJ and Friends offering an Amazon Fire Tablet with some of their apps on it . Looks like a very good educational tool and it's advertised for ages 6 to 8. Google it and see.

Pricesmart carries the Kindle Fire also.

adnj

Your pic isn't loading for me.

adnj

I'm not sure if they are still in business but you can try Fusaa Ltd.

adnj

Is there a smart plug or other device that can give me an alert by phone or alexa that the dryer is done drying my clothes? The buzzer noise even though its loud and annoying to ppl in a nearby tv room it can't be haerd upstairs in my bedroom. The dryer is a 220V. The buzzer on most dryers is a 12V...

adnj

FWIW, Bhagwansingh Piarco sold out of 5m tape measures the day after this happened.

adnj

It was recently put up, so a driver would hardly likely have known. It was a regular truck , so no escort vehicle. Reversing a truck and trailer back to Valsayn in traffic is very challenging if not nearly impossible. If it was erected just a few more feet to the east , there would have been an opp...

adnj

I still can't understand where a truck will go if he reach the barrier and is too tall to go under. The driver is tasked with knowing of low clearances along a route. If the load is oversized, an escort vehicle may have a verticle mast to check clearance far ahead of the oversized load. If the semi...

adnj

K_J_R wrote:i think i saw a sign saying 4.5m clearance on that bridge.

unless i imagined that.

and the bridge looks definitely lower than the walkovers. why make it lower? that make no sense.

It does say 4.5m. Pedestrian walkways are typically higher than road bridges as a safety measure.