TriniTuner.com  |  Latest Event:  

Forums

Search found 15780 matches

by crazybalhead
May 14th, 2004, 9:35 am
Forum: HONDA
Topic: Door Lock
Replies: 13
Views: 1681

Yep. I used a small nail though. Yuh have to be creative with them kinda problems
by crazybalhead
May 13th, 2004, 5:50 pm
Forum: HONDA
Topic: Trottle body
Replies: 19
Views: 2258

Not necessarily. Hotter air with a greater volume can have the same mass as colder air with smaller volume. So more air is not necessarily more mass. This is why I think Honda measures pressure, that way the volume over temperature ratio is measured. So a calculation using Air intake temp vs Mass is...
by crazybalhead
May 13th, 2004, 5:18 pm
Forum: AUTOMOTIVE TECH
Topic: info: Anyone knows anyone who does port & polishing
Replies: 12
Views: 1543

The stock B16 ports are very efficient to start with. So is the stock exhaust manifold, extractors only add a small amount of performance. Try other mods before you port and polish.
by crazybalhead
May 13th, 2004, 5:00 pm
Forum: HONDA
Topic: Door Lock
Replies: 13
Views: 1681

If you have the two pieces epoxy them together with the paper clip. Mine wukkin so years now.
by crazybalhead
May 13th, 2004, 4:59 pm
Forum: HONDA
Topic: 2002 Civic Si Chassis, K20A2 RSX Type-S Engine
Replies: 11
Views: 5308

I have the latest SCC they swapped a K24 with a K20 head. The newestest frank. BAD.
by crazybalhead
May 13th, 2004, 4:57 pm
Forum: HONDA
Topic: Still smokin! Please help.
Replies: 10
Views: 1572

Bad rings boy, how much times we telling yuh that. You are getting blow-by. And I wouldn't run my engine on one quart of oil if I were you.
by crazybalhead
May 13th, 2004, 4:55 pm
Forum: HONDA
Topic: Trottle body
Replies: 19
Views: 2258

That wouldn't be a major gain. I don't think so. And like I said as long as he not above 0 PSI the map will compensate "to a point", the point of course being the maximum advance and fuel that the stock computer can set.
by crazybalhead
May 13th, 2004, 4:53 pm
Forum: HONDA
Topic: Advice on engine upgrade, please
Replies: 9
Views: 1464

Yuh know! But it sounding like an automatic OBD II B16A is the way to go. That will run you about 6000-8000 plus 2000 installation and cater 1000 for miscellaneous sh.it Look for a front cut with ALL the parts including mounts and axles BEFORE you start. I also would recommend Autonation to do the s...
by crazybalhead
May 13th, 2004, 4:50 pm
Forum: HONDA
Topic: rear shocks EK3
Replies: 5
Views: 1157

MAN, what kinda question is that, just open up the little cover and check nah!!! But I believe it is two 14's and a 17.
by crazybalhead
May 13th, 2004, 4:48 pm
Forum: HONDA
Topic: Trottle body
Replies: 19
Views: 2258

Honda does not operate on air MASS, but rather manifold absolute pressure, so as long as yuh not boosting, the MAP sensor should compensate to a point.
by crazybalhead
May 13th, 2004, 11:14 am
Forum: AUTOMOTIVE TECH
Topic: Ways to tell that your car is pinging/knocking
Replies: 24
Views: 2007

If yuh hear it going

"pingpillingpingpingping"

then it pinging

If it going

"koncknocknocknock"

Then it knocking.



Serious.












:lol: :lol: :lol:
by crazybalhead
May 13th, 2004, 11:13 am
Forum: AUTOMOTIVE TECH
Topic: G-TECH PROBE INFO
Replies: 9
Views: 1325

ZORT wrote:
is best you make a run by the dyno in Penal and try to hit a timing session in Wallers for your times and power outputs

Do you know how many different mods you can do to your car inbetween timing sessions>>? :roll:


Doh talk about if yuh DON't run with timing lights, WUSS YET.
by crazybalhead
May 12th, 2004, 10:22 am
Forum: AUTOMOTIVE TECH
Topic: Question on synthetic oils
Replies: 57
Views: 5874

i agree with mitsu exec...........the performance with fully synthetic oil is something the driver has to experience by himself.........im talking about a higher hp output.......thinner so more lubrication in the tranny.......i have swithced to mobil about 9mths now and i am very pleased..............
by crazybalhead
May 7th, 2004, 5:12 pm
Forum: HONDA
Topic: Engine Mounts concern in hondas.
Replies: 29
Views: 2328

I saw the hasport mounts are solid urethane. That has to be for a good reason man. And with all that torque and hard launches yuh must buss that stock mount. I feel it was bad in the first place.
by crazybalhead
May 5th, 2004, 8:41 am
Forum: HONDA
Topic: Over heating problems
Replies: 18
Views: 1781

I feel there is a clog somewhere. The radiator needs to be taken down and cleaned or replaced. More than likely that's your problem.
by crazybalhead
May 5th, 2004, 8:38 am
Forum: HONDA
Topic: B20 swap in an EG8 : How hard is it???
Replies: 40
Views: 4700

No such thing.
by crazybalhead
May 4th, 2004, 10:52 am
Forum: AUTOMOTIVE TECH
Topic: Tyre Decision: Which to Buy? Pros & Cons...URGENT!!
Replies: 32
Views: 3281

I runnin the 712 ecsta ZR rated 280 threadware and they are very nice. I guess any 40 series tire would be pothole prone, I damaged two already, but I would still recommend them.
by crazybalhead
May 4th, 2004, 9:43 am
Forum: HONDA
Topic: B20 swap in an EG8 : How hard is it???
Replies: 40
Views: 4700

X cable might be different too.
by crazybalhead
May 3rd, 2004, 7:53 am
Forum: HONDA
Topic: Bouncy car
Replies: 9
Views: 1708

996vtwin wrote:If your shocks are bottoming out then you need to remove some bump stop. Does it bottom out?...on a corner with say a slight depression.


Mine doing that. What's your diagnosis doc??
by crazybalhead
May 3rd, 2004, 7:09 am
Forum: HONDA
Topic: B20 swap in an EG8 : How hard is it???
Replies: 40
Views: 4700

PLACIDE...You will get yourself in trouble boy.
by crazybalhead
April 29th, 2004, 9:19 am
Forum: HONDA
Topic: B20 swap in an EG8 : How hard is it???
Replies: 40
Views: 4700

Yuh wasting time with that B20 dread. And as I have told you before, yuh looking for trouble.
by crazybalhead
April 19th, 2004, 3:49 pm
Forum: HONDA
Topic: Smokin!!
Replies: 23
Views: 1925

Yuh rings must be a bit worn.
by crazybalhead
February 27th, 2004, 11:28 am
Forum: HONDA
Topic: type R or h22 what is faster.......?
Replies: 45
Views: 4547

Hear nah X2 boy, if somebody sits in my hatch (as I am sure you would agree) the handling changes noticeably, imagine putting 100lbs in the nose of a light civic. I guess if you upgrade the suspension properly it will compansate accordingly.
by crazybalhead
February 27th, 2004, 9:55 am
Forum: HONDA
Topic: type R or h22 what is faster.......?
Replies: 45
Views: 4547

But the handling will suck with the H22
by crazybalhead
February 5th, 2004, 3:15 pm
Forum: AUTOMOTIVE TECH
Topic: Calculating MPG in Trinidad
Replies: 53
Views: 4373

sleep driving boy. Vtec sometimes.
by crazybalhead
February 5th, 2004, 1:43 pm
Forum: AUTOMOTIVE TECH
Topic: Calculating MPG in Trinidad
Replies: 53
Views: 4373

I only gettin 22 MPG...hmmmmm over rich??
by crazybalhead
February 5th, 2004, 12:57 pm
Forum: AUTOMOTIVE TECH
Topic: Who does Rim Repairs/Painting?
Replies: 24
Views: 2316

arnold_k69 wrote:i got a rim repair by mileage mack, did a pretty decent job and the fnish was good


Mileage mack also sends their rims by Marcus or Peakes to repair, and then charge you an arm and leg on top of that.
by crazybalhead
February 5th, 2004, 12:56 pm
Forum: AUTOMOTIVE TECH
Topic: Who does Rim Repairs/Painting?
Replies: 24
Views: 2316

Cool Hip Jim wrote:anyone ever painted rims by marcus?


YES YES, read nah man.
by crazybalhead
February 4th, 2004, 5:56 pm
Forum: AUTOMOTIVE TECH
Topic: Who does Rim Repairs/Painting?
Replies: 24
Views: 2316

Jesus H Christopher, click the link on top yuh head!!!
by crazybalhead
February 4th, 2004, 1:44 pm
Forum: AUTOMOTIVE TECH
Topic: Who does Rim Repairs/Painting?
Replies: 24
Views: 2316

Listen, marcus does excellent work, do not bother to look around. Dean will either send it right by marcus or peakes to do anyway. Peakes does a good job with cracks, but I don't know about refinishing. I have done two rims with the outer lip bent by Marcus, I recieved them the same day I dropped th...

Go to advanced search