TriniTuner.com  |  Latest Event:  

Forums

:::The Official CK4/CB MIVEC Thread:::

Mitsu Lancer, Evo, GSR, MIVEC, 4G**, GDI, Galant, Outlander, L200 Sportero/Triton etc.

Moderator: 3ne2nr Mods

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

:::The Official CK4/CB MIVEC Thread:::

Postby Morpheus » April 22nd, 2010, 5:01 pm

Ok I rather search for one thread than having to search all over the place for info.

All Mivec info/tips should go here

CK4 MIVEC, what fluids allyuh using? Engine and transmission.
Last edited by Morpheus on April 24th, 2010, 10:59 am, edited 1 time in total.

Advertisement
User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Postby Morpheus » April 22nd, 2010, 5:09 pm

Also what suspension parts are interchangable between the Regular CK4 and the CK4 MIVEC. I hear the sway bar rubber is different because the MIVEc sway bar thicker.

I looking to do some suspension work, doh wanna get tied up with the wrong bushing/rubbers :?

User avatar
Animal Pak
3NE 2NR for life
Posts: 169
Joined: September 13th, 2009, 9:16 pm

Postby Animal Pak » April 22nd, 2010, 9:04 pm

Engine - Shell Helix 10W 40

Transmission - Quaker State ATF but anything Dextron III will work

Rear shocks same as normal ck 4, front shocks different.

I believe the control arms are interchangeable with evo 4 but not sure.

User avatar
MISHI
3NE 2NR Aficionado
Posts: 5423
Joined: May 14th, 2003, 4:00 pm
Location: Location: Location!
Contact:

Postby MISHI » April 22nd, 2010, 9:04 pm

As long as it's a MIVEC thread.


CB fellas if you're gonna change over to a MIVEC gearbox, make sure you get a set of MIVEC front axles else you will be a little short on the left side using back your original ones even if you have a manual inner cup.

User avatar
fras
Chronic 2NR
Posts: 2129
Joined: August 25th, 2005, 8:34 pm
Location: Penal

Postby fras » April 23rd, 2010, 10:41 am

Mivec Servicing
Suspension Mods
Engine Mods
Workshop Manuals
1.8 Mivec Conversion
+More

http://www.mivec.co.nz/forums/viewforum.php?f=35
Last edited by fras on April 24th, 2010, 11:29 am, edited 1 time in total.

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Postby Cardo-MR » April 24th, 2010, 2:41 am

Morpheus, what's the part no# on your ECU by chance??Is your Mivec a SDM or JDM?
I want to compare it to mine,which ends in 3396.

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Postby Morpheus » April 24th, 2010, 10:58 am

Man I have no clue. Will give it a check for you.

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Postby Cardo-MR » April 25th, 2010, 8:31 pm

Ne word?If yuh car came with d 220km on the instrument panel...its SDM

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Postby Morpheus » April 25th, 2010, 11:49 pm

Dunno. Bought the car with a regular CK auto instrument panel. Anything else I can check to verify?
Last edited by Morpheus on June 21st, 2012, 2:39 am, edited 1 time in total.

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Postby Cardo-MR » April 26th, 2010, 12:55 am

Ent d mivec you bought was omegajedi green mivec?? If so its ah SDM.
When you geh chance just take a look @ the ECU & tell me the Part # on yours.....daz all i need.

User avatar
rjaggs
Chronic TriniTuner
Posts: 565
Joined: October 30th, 2007, 1:07 pm
Location: Right here...

Postby rjaggs » April 28th, 2010, 12:48 pm

can anyone confirm if the jdm ecu number ends in 5299?

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Postby Cardo-MR » April 28th, 2010, 3:08 pm

rjaggs, Yea it does. Both Auto & Manual I believe.
that's why i want to confirm the SDM model if it ends with 3396.

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Postby Morpheus » April 28th, 2010, 4:17 pm

^^I' ll try to get that info after the football game and after the sun go down

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Postby Morpheus » April 29th, 2010, 4:39 pm

Oh gorm they have to hide ECU away so??? Will make another attempt in better lighting

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Postby Cardo-MR » April 30th, 2010, 11:27 pm

any word yet??

User avatar
rjaggs
Chronic TriniTuner
Posts: 565
Joined: October 30th, 2007, 1:07 pm
Location: Right here...

Postby rjaggs » May 1st, 2010, 9:16 pm

Cardo-MR wrote:rjaggs, Yea it does. Both Auto & Manual I believe.
that's why i want to confirm the SDM model if it ends with 3396.


I think the auto ecu different

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Postby Cardo-MR » May 2nd, 2010, 2:15 am

rjaggs, Which harness you using auto or manual?after yuh conversion

User avatar
rjaggs
Chronic TriniTuner
Posts: 565
Joined: October 30th, 2007, 1:07 pm
Location: Right here...

Postby rjaggs » May 3rd, 2010, 10:03 pm

auto ftw...until i could locate a manual harness

User avatar
MISHI
3NE 2NR Aficionado
Posts: 5423
Joined: May 14th, 2003, 4:00 pm
Location: Location: Location!
Contact:

Postby MISHI » May 4th, 2010, 12:15 am

any of you have any idea as to the length of the axles? (CB)

Wolla
3NE 2NR for life
Posts: 200
Joined: November 27th, 2006, 9:31 pm
Location: West

Postby Wolla » May 4th, 2010, 11:37 am

What spark plug do you guys suggest to be used for the Mivec? I have a 4g93 block with Mivec head, any spark plug suggestions?

Thanks

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Postby Cardo-MR » May 4th, 2010, 10:44 pm

Wolla, I using the original Mivec Plug BKR7EKC-N....if that doh work for you try the GDI double pin plug as it a lil longer than the mivec.

Which 93 block you using??

Morpheus, any word as yet?? Or do I have to come by Nestle & take it out to find out?

User avatar
trinibajan34
3NE2NR is my LIFE
Posts: 758
Joined: November 21st, 2007, 2:47 pm
Location: san juan

Postby trinibajan34 » May 5th, 2010, 11:58 am

Question ,how does the car feel when mivec has kicked in (car response) ,how does the engine sound. oh and where wolud ibe able to get a mivec controller if one is blown.

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Postby Morpheus » May 5th, 2010, 3:24 pm

Morpheus, any word as yet?? Or do I have to come by Nestle & take it out to find out?


^^Boy u believe I nearly tell yuh check me the other day. I working some funny shifts these past few weeks. And that sun is a killer when I do get a lil chance(I choose to avoid it-LoL that sun in melt mode these days).

I'm "OFF" today and tomorrow. Have PTA meeting this afternoon so tomorrow I will do that tomorrow

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Postby Morpheus » May 5th, 2010, 3:25 pm

Wolla, I using the original Mivec Plug BKR7EKC-N....if that doh work for you try the GDI double pin plug as it a lil longer than the mivec.


^^Where u got those plugs?

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Postby Cardo-MR » May 5th, 2010, 7:24 pm

Morpheus, Ok......well I Patiently waiting. Got the plugs by Sheriff's in south. $65 each

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Postby Morpheus » May 6th, 2010, 5:08 pm

Cardo sorry for the long wait.

Yes the ECU has 3396 in large CAPS

Dunno if u wanted it but the number below that is E2T65698

Image

User avatar
trinibajan34
3NE2NR is my LIFE
Posts: 758
Joined: November 21st, 2007, 2:47 pm
Location: san juan

Postby trinibajan34 » May 6th, 2010, 10:20 pm

so no answer to my question ? :(

User avatar
Cardo-MR
Sweet on this forum
Posts: 361
Joined: November 28th, 2007, 4:07 pm
Location: SOUTH!

Re: :::CK4/CB MIVEC and MIVEC Swap Thread:::

Postby Cardo-MR » May 10th, 2010, 10:16 pm

Morpheus ...thanks...its the same.

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Re: :::CK4/CB MIVEC and MIVEC Swap Thread:::

Postby Morpheus » May 11th, 2010, 9:15 am

^^Cool man NP

User avatar
Morpheus
TriniTuner 24-7
Posts: 10655
Joined: July 22nd, 2004, 2:24 am

Re: :::CK4/CB MIVEC and MIVEC Swap Thread:::

Postby Morpheus » May 17th, 2010, 1:02 am

WHo's a good MIVEC mechanic? Who is dis Anil guy I keep hearing about. Any referrals?

Advertisement

Return to “MITSUBISHI”

Who is online

Users browsing this forum: No registered users and 2 guests