TriniTuner.com  |  Latest Event:  

Forums

Show us your BJ!

MAZDA People United - it continues here

Moderator: 3ne2nr Mods

User avatar
ShaqThom
Sweet on this forum
Posts: 273
Joined: May 16th, 2012, 6:04 pm

Re: Show us your BJ!

Postby ShaqThom » December 5th, 2016, 11:54 pm

Need d cash to finish a project smeags! Was hoping I got it sold before years end!

Advertisement
User avatar
smeags
Riding on 13's
Posts: 10
Joined: December 11th, 2011, 1:11 pm

Re: Show us your BJ!

Postby smeags » December 19th, 2016, 1:11 am

Ok cool. So u out the game there

User avatar
Zorak
Sweet on this forum
Posts: 292
Joined: September 7th, 2007, 10:28 am
Location: Location, Location!

Re: Show us your BJ!

Postby Zorak » March 1st, 2017, 12:59 pm

Hey Fellas,
I've got a Racing Beat rear sway bar and a Mazdaspeed exhaust for sale. $900 each.

User avatar
NR8
Riding on 17's
Posts: 1527
Joined: January 14th, 2012, 2:20 pm

Re: Show us your BJ!

Postby NR8 » March 18th, 2017, 1:59 am

Hey guys, recently got a 1.6 Singapore BJ and just read through all 69 pages of the thread! I've already got a few upgrades planned including suspension and brakes, if I can find them.

I will be installing a Bluetooth head unit and would like to know how to go about removing the finishers around the centre console to get to the deck? Also, are there any factory holes/grommets in the firewall that I can use to run a power wire from the battery to an amp?

I'll also be doing an ATF drain and refill soon and intend to install a transmission cooler while I'm at it. However I recall someone saying earlier in the thread that the BJ tranny doesn't have a strong pump and that too large a cooler may cause failure. I have a Hayden 403 cooler measuring 12.5" x 7.5" x 0.75". Is this an acceptable size? Should I run the cooler in series with the radiator or blank off the radiator lines and run direct to cooler alone? Also, will I have to remove the grill and bumper to install it?

Thanks in advance.

User avatar
libra
3NE2NR is my LIFE
Posts: 770
Joined: March 25th, 2009, 10:40 pm
Location: central

Re: Show us your BJ!

Postby libra » March 22nd, 2017, 12:35 am

u have belly to read all that lol .. for the console u dont need to take out the finisher to take out the deck .. it has tabs at the side of the deck itself ... it has a hole where the clutch pedal supposed to be if u dont plan to go manual so u can pass the wire tru there ... that size cooler should be good and i blanked the rad one ... yes removing the bumper will make the job easy

User avatar
NR8
Riding on 17's
Posts: 1527
Joined: January 14th, 2012, 2:20 pm

Re: Show us your BJ!

Postby NR8 » April 6th, 2017, 10:57 am

libra wrote:u have belly to read all that lol .. for the console u dont need to take out the finisher to take out the deck .. it has tabs at the side of the deck itself ... it has a hole where the clutch pedal supposed to be if u dont plan to go manual so u can pass the wire tru there ... that size cooler should be good and i blanked the rad one ... yes removing the bumper will make the job easy

Hey libra, thanks for the info man. Below is a pic of my original deck as it came from Singapore. How do I get that out?
Image

User avatar
libra
3NE2NR is my LIFE
Posts: 770
Joined: March 25th, 2009, 10:40 pm
Location: central

Re: Show us your BJ!

Postby libra » April 7th, 2017, 12:50 pm

Those pioneer deck keys should work ... has tabs on the sides of the deck ( center of em has a lil slot for the key to push in ) wen ya push i the keys the deck should pull out

User avatar
NR8
Riding on 17's
Posts: 1527
Joined: January 14th, 2012, 2:20 pm

Re: Show us your BJ!

Postby NR8 » April 7th, 2017, 1:34 pm

libra wrote:Those pioneer deck keys should work ... has tabs on the sides of the deck ( center of em has a lil slot for the key to push in ) wen ya push i the keys the deck should pull out

I tried a couple of those but it wouldn't budge. The keys were actually stuck and didn't want to come out. I had to use a pliers to pull them out and the little notches on them got bent backwards.

User avatar
libra
3NE2NR is my LIFE
Posts: 770
Joined: March 25th, 2009, 10:40 pm
Location: central

Re: Show us your BJ!

Postby libra » April 7th, 2017, 3:47 pm

Well pull out the pocket n see wa goin on ... has tabs on the sides of it ... hadda press it from d inside .. take out the glove box n send up ur hand to reach one side n try from d other

User avatar
mazdanavisport
Street 2NR
Posts: 55
Joined: August 27th, 2008, 11:50 am
Location: All over

Re: Show us your BJ!

Postby mazdanavisport » April 20th, 2017, 1:01 pm

Good day gentlemen, looking for roof rail or rack for the sport 20, mines damage, any help will greatly appreciated

ahing6
Ricer
Posts: 24
Joined: December 25th, 2013, 9:57 pm

Re: Show us your BJ!

Postby ahing6 » November 13th, 2017, 7:43 am

looking for damaged BJ or BH drivers door

Advertisement

Return to “MAZDA”

Who is online

Users browsing this forum: No registered users and 4 guests