Energy Sector Thread - Operators, Engineers, Technicians Et Al

sinister_14 · Postby **sinister_14** » November 11th, 2017, 8:57 pm

eitech wrote:Jus heard upstream reformer tubes blow out

This was bound to happen all their good operators leave to go cgcl....rip lpsl...

DreamWeaver · Postby **DreamWeaver** » November 11th, 2017, 8:58 pm

eitech wrote:Jus heard upstream reformer tubes blow out

daz it? daz small thing. m4 was blowing tubes every week earlier this year. lol. crimp tube and start back up then?

sinister_14 · Postby **sinister_14** » November 11th, 2017, 9:11 pm

DreamWeaver wrote:
eitech wrote:Jus heard upstream reformer tubes blow out

daz it? daz small thing. m4 was blowing tubes every week earlier this year. lol. crimp tube and start back up then?

Dats not small thing d reformer blow up...

sMASH · Postby **sMASH** » November 11th, 2017, 9:16 pm

Fleck

sMASH · Postby **sMASH** » November 11th, 2017, 9:18 pm

Dem fellas is one set ah panty man. 'sworn secrecy'... Like a crack where to a dealer.

sMASH · Postby **sMASH** » November 11th, 2017, 9:27 pm

Somebody screw up real bad.... I don't have details but, somebody gonads will be receding back up into the body cavity.

sinister_14 · Postby **sinister_14** » November 11th, 2017, 9:28 pm

sMASH wrote:Dem fellas is one set ah panty man. 'sworn secrecy'... Like a crack where to a dealer.

X1000.......all ah dem on that plant where d reformer blow up......setta BUGWAAANAAA...

DreamWeaver · Postby **DreamWeaver** » November 11th, 2017, 9:31 pm

sinister_14 wrote:
DreamWeaver wrote:
eitech wrote:Jus heard upstream reformer tubes blow out

daz it? daz small thing. m4 was blowing tubes every week earlier this year. lol. crimp tube and start back up then?

Dats not small thing d reformer blow up...

doh sheit me up. serious?! weyz insurance premiums gonna go up! anybody get hurt? i didn't see anything in news

sinister_14 · Postby **sinister_14** » November 11th, 2017, 9:36 pm

DreamWeaver wrote:
sinister_14 wrote:
DreamWeaver wrote:
eitech wrote:Jus heard upstream reformer tubes blow out

daz it? daz small thing. m4 was blowing tubes every week earlier this year. lol. crimp tube and start back up then?

Dats not small thing d reformer blow up...

doh sheit me up. serious?! weyz insurance premiums gonna go up! anybody get hurt? i didn't see anything in news

No injury....everything keeping hush hush....for now....it have something called karma....and this happen because that company does only bad treat their employees....

sMASH · Postby **sMASH** » November 11th, 2017, 9:37 pm

Is every week, sometime twice a week I was up m2 in fire suit crimping tubes

sMASH · Postby **sMASH** » November 11th, 2017, 9:40 pm

It's not a 'typical' tube rupture... A "lil" more happen.
All I will say, is if u like to push tings to the limits, sometimes u exceed those limits.

DreamWeaver · Postby **DreamWeaver** » November 11th, 2017, 9:43 pm

ent that is d same plant dat had some explosion on it a few years ago?

sinister_14 · Postby **sinister_14** » November 11th, 2017, 9:49 pm

DreamWeaver wrote:ent that is d same plant dat had some explosion on it a few years ago?

Yup d lts inlet blow up...

DreamWeaver · Postby **DreamWeaver** » November 11th, 2017, 9:51 pm

weyz. daz rough tho. i glad nobody get hurt.

sMASH · Postby **sMASH** » November 11th, 2017, 10:16 pm

sinister_14 wrote:
DreamWeaver wrote:ent that is d same plant dat had some explosion on it a few years ago?

Yup d lts inlet blow up...

Wait, I thought u talking about when the HP bfw turbine had exploded

Supervisor saved those guys lives.

rmrunner · Postby **rmrunner** » November 11th, 2017, 10:27 pm

Reformer damage nothing new with them. I remember few years ago when over a hundred tubes were damaged on M1 plant. Set a crackshots

sinister_14 · Postby **sinister_14** » November 11th, 2017, 10:36 pm

sMASH wrote:
sinister_14 wrote:
DreamWeaver wrote:ent that is d same plant dat had some explosion on it a few years ago?

Yup d lts inlet blow up...

Wait, I thought u talking about when the HP bfw turbine had exploded

Supervisor saved those guys lives.

Nope...supervisor save himself...resign rite after...cause they trottle steam inlet on turbine....and mash up d pump....

DreamWeaver · Postby **DreamWeaver** » November 11th, 2017, 11:03 pm

i wonder how much people gonna get blame for this one now. for sure the whole ops shift might get suspended or worse. dat company cyah afford to do that either since cgcl take some of their best.

sMASH · Postby **sMASH** » November 11th, 2017, 11:21 pm

Well, they swore themselves to secrecy, so they will take any jamming offered. Justified or not.

Panzzies.

Me, i preferred to take down turbine via the steam inlet. Just make. Sure that it coasts down and doesn't begin to backspin. And. In that case, if u can throttle the discharge to prevent flow or open up the steam inlet a bit to give it more forward rotation.

But then again I grew up with valves seating off well and check valve holding. That fertilizer place, half the things don't work properly and the other half fail in a timing.

And then again, when I left where I grew up, a short time after HP boiler tunes went shooting into The reformed gas piping leaving the boiler. And before that distribution laterals were ejected from the side of a cooling tower. I called that the M4 attempt at a space program.

De Dragon · Postby **De Dragon** » November 11th, 2017, 11:41 pm

rmrunner wrote:Reformer damage nothing new with them. I remember few years ago when over a hundred tubes were damaged on M1 plant. Set a crackshots

Pfft, M3 destroyed all 384 of theirs in the early, TTMC days

Cantmis · Postby **Cantmis** » November 12th, 2017, 1:12 am

: Wilson_The_Volleyball.jpg (10.98 KiB) Viewed 4771 times

sMASH · Postby **sMASH** » November 12th, 2017, 5:35 am

De Dragon wrote:
rmrunner wrote:Reformer damage nothing new with them. I remember few years ago when over a hundred tubes were damaged on M1 plant. Set a crackshots

Pfft, M3 destroyed all 384 of theirs in the early, TTMC days

Thst guy got large after

vaiostation · Postby **vaiostation** » November 12th, 2017, 8:31 am

"Resignations" incoming!!!
"Promotions" incoming!!!

DreamWeaver · Postby **DreamWeaver** » November 12th, 2017, 8:48 am

vaiostation wrote:"Resignations" incoming!!!
"Promotions" incoming!!!

for real. in typical fashion. you forgot the "suspensions" incoming! though

eitech · Postby **eitech** » November 12th, 2017, 9:15 am

vaiostation wrote:"Resignations" incoming!!!
"Promotions" incoming!!!

Promotions not saving the resignations nah

trinidrift · Postby **trinidrift** » November 15th, 2017, 2:43 pm

Anyone heard bp want operators? Can someone send the link if you have it?

Kixy · Postby **Kixy** » November 15th, 2017, 5:09 pm

sinister_14 wrote:
DreamWeaver wrote:
eitech wrote:Jus heard upstream reformer tubes blow out

daz it? daz small thing. m4 was blowing tubes every week earlier this year. lol. crimp tube and start back up then?

Dats not small thing d reformer blow up...

Nobody get a picture or video of this yet?

Apparently d damage rel bad, i heard ammonia gonna be down for a good few months.

eitech · Postby **eitech** » November 15th, 2017, 5:35 pm

Kixy wrote:
sinister_14 wrote:
DreamWeaver wrote:
eitech wrote:Jus heard upstream reformer tubes blow out

daz it? daz small thing. m4 was blowing tubes every week earlier this year. lol. crimp tube and start back up then?

Dats not small thing d reformer blow up...

Nobody get a picture or video of this yet?

Apparently d damage rel bad, i heard ammonia gonna be down for a good few months.

Well i heard it was real bad too. Proman already inside. Heard they project 3- 6 wks. My padna done say he fed up pull burnt cables. Lol

gencon · Postby **gencon** » November 19th, 2017, 9:14 am

kavaninho wrote:A link is right. That's the hiring medium now.

was home for almost 2 years got a link up because of networking, got a position as quality control technician 2-3 year contract and I doh even have a degree :lol:

Postby **nervewrecker** » November 19th, 2017, 9:19 pm

instantfrugality wrote:
kavaninho wrote:A link is right. That's the hiring medium now.

was home for almost 2 years got a link up because of networking, got a position as quality control technician 2-3 year contract and I doh even have a degree

Thats how you do it. Gotta make yourself known.