TriniTuner.com  |  Latest Event:  

Forums

Keep cool! All about your cooling system.....

Diesel, Gas, 4x4, 4x2

Moderator: 3ne2nr Mods

Forum rules
This forum is for discussions on Trucks and Pickups only!
DO NOT POST ADS IN HERE
WTB (Want to buy), LF (Looking for), EOI (Expression of Interest) or FS (For sale) topics etc will be deleted.
If you are looking for a part please search or post in the Auto Parts Classifieds.
Please keep all discussion professional and technical. Opinions are welcomed, however trolling, spamming and bashing will not be tolerated.
User avatar
lighthammer
punchin NOS
Posts: 4519
Joined: April 15th, 2010, 2:35 pm
Location: Somewhere over the rainbow...

Keep cool! All about your cooling system.....

Postby lighthammer » October 3rd, 2012, 10:18 am

Yo fellas,

While doing some research on an overheating problem, I came across this Wiki with loads of useful information on how your cooling system.

http://www.crankshaftcoalition.com/wiki/Bulletproof_cooling_system


It's very informative on how your cooling system works, the different components to it and how they are all related. Easy to read, easy to comprehend and apply to almost any cooling problem you may have.

*note - it's not written specifically for Diesel vehicles, but it applies to almost any vehicle. Also, all units quoted are in Farenheit.





Some snippets from the site:
How the cooling system works

Note- All temperatures are in degrees Fahrenheit.

The cooling system works by absorbing, transporting, and dissipating heat. Therefore, anything that impedes any of those functions can cause overheating:

Heat flows from higher temperature to lower temperature. A car's engine is generally cooled by keeping it in constant contact with a cooler fluid. As soon as that circulation is impeded, temperatures rise. The radiator must also be working efficiently to transfer engine heat to the atmosphere, and the thermostat must be in perfect working order.

The cooling system transports heat from the engine, into the coolant, and out into the atmosphere. If the amount of heat that it picks up from the engine is roughly equal to the amount of heat that it dispenses to the atmosphere, the engine temperature will stay constant.

As long as the coolant is taking on roughly the same amount of heat that it can dissipate, it will be effective.

It's easy to assume that cooler temperatures are better. However, they really just give you more of a buffer before the boiling point is reached. However, a properly functioning cooling system can really operate just fine at any temperature under its boiling point. If a cooling system is taking on more heat than it can dissipate, it will eventually overheat, regardless of the temperature at which the thermostat opens.

This is why using a lower-temperature thermostat often doesn't solve overheating problems. The heat that the coolant takes on must be roughly equal to the heat that it dissipates.


Overheating and its causes

"Overheating" essentially just means that the cooling system is taking on more heat than it can dissipate. When coolant takes on too much heat, it boils. This means that the water jacket surfaces will be covered with more steam than coolant. Steam can't absorb heat like coolant can, and this exponentially exacerbates the problem: more heat results in more steam, which leads to less effective coolant, and, in turn, more boiling of coolant.

Overheating can be caused by anything that decreases the cooling system’s ability to absorb, transport and dissipate heat. Some causes of overheating are:

Low coolant level, loss of coolant, or insufficient coolant capacity
Buildup of deposits that cause poor conduction of heat into the cooling system
A thermostat that won't open
Poor airflow through the radiator
Damaged or worn fan clutch, or broken fan
Collapsed radiator hose
Loose or defective water pump impeller
Defective radiator cap
Late ignition timing

Bulletproof cooling system tips

Clogging and leaks are two of the most common radiator problems. Bugs, dirt, and debris can block airflow, and limit the radiator's heat-dissipating characteristics. Thus, it's recommended to "back flush" the radiator and cooling system when changing coolant. This helps to clean out deposits, and flushes the remaining coolant from the engine block. You can back flush the radiator by running water through it in the opposite direction of regular flow. Typically, after draining the radiator a t-fitting can be installed in the heater inlet hose. This fitting gets connected to a pressurized water hose, and the system is reverse flushed. Do this until clean water emerges.
A rough guide is to use a radiator at least as large as the one that was originally used to cool the engine, with the same or more radiator cores. However, it's important to note that additional rows don't add a proportional amount of cooling, i.e. a 3-row radiator does not necessarily offer 50% more cooling than a 2-row radiator. This is because subsequent rows receive warm air from the rows in front of them. However, adding radiator frontal area IS proportional, but this usually causes fitment issues, so additional rows are generally the only viable choice. Also the radiator design and materials can have an effect on the radiator efficiency; a larger radiator is not necessarily a better radiator.
Oftentimes, the cheapest and most bulletproof way is to use the largest radiator that will fit, along with the fan type and size, and shroud that was designed for the radiator from the factory.
Use a full shroud, with the radiator positioned so that the fan blades are half-in and half-out of the shroud hole, and no more than 1" of clearance between the shroud and the fan blade tips (just enough to prevent interference when the motor rocks on its rubber mounts).
Fan recommendations: OEM 18 inch, 7-blade steel fan with 2" to 2-3/4" pitch. The pitch of a fan can be measured by laying the fan down on a flat surface and measuring from the flat surface to the edge of the fan blade. Fans that are relatively flat (such as a flex fan) may not move enough air at idle and low engine RPM to cool the engine properly.
When possible, use a thermostatically controlled fan clutch. While a thermostatically modulated fan clutch is an effective means of operating the cooling system's fan, a worn or defective fan clutch can cause overheating if left undiagnosed. Sometimes they may appear to be OK when cold but they will free-wheel when hot.
Water pump and crankshaft pulleys sized according to what was on the engine from the factory. On a street motor, shoot for 1.2 to 1.3 times crank speed for pump pulley speed. This is usually true until you get to 3.55 gears and numerically higher, then 1:1 works better. Most 1960s muscle cars are 1:1. Sustained pump speeds over 4200 rpm can cause cavitation. Race vehicles may use a 2.3:1 ratio for a 9000-plus rpm engine.
On a carburetor-equipped engine, often a 180º thermostat is used, although a little hotter thermostat rating (190º-195º) may make the motor more responsive and add a little fuel mileage. It may also help to burn off some of the by-products of combustion, such as moisture and acids which form and get into the oil. Motors using EFI induction should use the thermostat temperature specified by the factory for that particular motor to prevent false input to the computer and consequent problems. The sensor pill goes toward the motor.
Use a spiral-wound spring in the bottom radiator hose, to prevent collapse of the hose.
Use the proper pressure cap for the radiator being used.
Ensure that there is adequate airflow from the engine compartment to allow the exit of the air drawn into the compartment. In custom applications this might require the removal or surgery of inner fender panels or using spacers to raise the hood of the car up an inch or two at the back.
Maintain the proper coolant/water mix to prevent freezing up in winter. Water transfers heat better than coolant, but some coolant must be used to prevent freezing. Using a 50/50 mix of coolant/water is a necessity for motors using aluminum parts. Plain water will turn aluminum into oatmeal.
Before installing the water pump, grasp the impeller with one hand and the drive hub with the other and twist to make sure the impeller is tight on the drive shaft. Not finding this problem beforehand can cause damage.
Although it may not be necessary, the concept of a "water pump conversion disc" can be researched. Flow Kooler originally marketed flat aluminum discs to be riveted to the backside of the stamped steel impeller of the water pump. With an iron impeller, a steel disc could be welded or brazed onto the impeller. Such a disc wouldn't be that difficult to make. Space the water pump backing plate back farther with a couple of gaskets to prevent interference of the rivet heads on the backing plate if riveting a disc to a stamped steel impeller. More info: brazing cast iron, Flow Kooler water pump conversion discs. This disc could make an appreciable difference in the flow of water at engine speeds under 3,000 RPM. On the other hand, Howard Stewart of Stewart Components (the guy with the water pump dyno), says that these discs have little to no effect.....


........ Coolant

Sometimes the key to a bulletproof system is what you put in it and how. You can't just open the radiator cap and dump anything in it. A 50/50 mix of water and ethylene glycol antifreeze boils at 225º if there is no pressure like when the radiator cap is open or defective. But if the cooling system is sealed and will hold pressure, a radiator cap rated at 15 psi will increase the boiling point of a 50/50 coolant mix to 265º. If the ratio of antifreeze to water is increased to 70/30 (the maximum recommended), the boiling point under 15 psi of pressure increases to 276º.

Water is the basis of coolant in most systems. Can the water that you start with have a detrimental effect on your cooling system? Yes! Water is not necessarily clean and free from contaminants. Water can contain acid, alkaline, foreign matter, etc. These contaminants can combine with the metal within the cooling system and contribute to plugging or slowing down the flow within the system. Today, you will find about 10 different antifreeze products and about 30 different additives for your cooling system. WHY do you need them? Good question!

Engineers have come up with cooling system recommendations based on their extensive research and their recommendations and warnings should be heeded. Your OEM dealer and manufacturer usually recommend using a 50/50 mix of antifreeze and water. This is to protect and prolong the life of cooling system metals and seals. Using unapproved additives or incorrect chemicals or ratios, etc., could be harmful to the cooling system and could also result in needless repair and expense.

There are additives of all sorts on the market. WaterWetter is one. John Deere Cool-Gard II is another. Note that tap water is sometimes not very good as it can contain minerals.

When you are refilling your cooling system, the radiator cap is open, and you pour directly into the system until it is full. "Full" means a level one inch less than the cap height. The engine should be warmed up and running at a fast idle of 1000 to 1200 rpm's. The engine is run until you can see movement in the radiator and a slight steam rises from the open cap outlet. If you have a gauge, verify that the temperature is at operating temperate of 160º to 195º. The cap is placed on the radiator outlet and turned until tight with the arrows aligned to point at the overflow outlet. The overflow bottle should be within its limits, which is usually marked on the container walls.

When you are adding to the system, do not open the radiator cap. Instead, add directly to the reservoir tank.

If you have ever watched a pot of water start to boil on the stove, you will know that tiny air bubbles start to rise from the bottom of the pot as the heat is raised. Adding a water 'conditioner' like WaterWetter to your coolant will break the surface tension and provide a greater contact area for the coolant. A wetting additive can supposedly decrease the temperature up to 20º F.

On a closed system with an overflow bottle, that the system should be filled to the top when it is at operating temperature. One of the advantages of this type of system is to reduce oxidation by eliminating all air from the system. Hence it then becomes a closed system. Why leave a head of air in the top of the radiator when you don't have to? Entrained air is sometimes difficult to get out of the system. The secret in the system lies in the overflow bottle. Coolant expands with heat, thus increasing the total water volume mass. When the pressure increase exceeds the radiator cap's capacity, the coolant passes from the radiator to the overflow bottle which is vented to the atmosphere. When the mass is cooled due to the air flow through the radiator or turning off the engine, the radiator cap will allow the coolant to be syphoned from the overflow tank back into the radiator/cooling system, thus keeping a set amount of mass present in the cooling system.


Radiator shroud

Radiator shrouds are devices that control the exiting air from the radiator and direct it to a rearward sucking electric or mechanical fan. Shrouds can be made from plastic, fiberglass, and metal (aluminum or steel). They cover the rear portion of the radiator. Allow air passing through the radiator to be ducted to the fan which directs air flow over the engine and out of the engine bay. In most cases, the mechanical fan will be inserted approximately 1/3 of the depth of the fan blades into the shroud, this is usually sufficient to draw a full charge of air and disburse it adequately without disrupting air flow.


Radiator cap

A radiator cap is important to the proper operation of the entire cooling system. The cap is designed to hold pressure in the system. Under pressure the coolant boils at a higher temperature than when non pressurized (approximately 3º per 1 psi) so a 10 psi cap will add 30º to the boiling point of the coolant. Check the cap gasket for cracks and other damage. If the cap pressure spring is badly rusted replace the cap, observing the pressure stamped on the old unit, acquire one with the same pressure rating. During inspection make sure that the radiator filler neck (where the cap lives) is clean and the sealing surfaces are undamaged.

A radiator with a nicked or damaged sealing surface can be repaired by employing a metal filled epoxy to fill the imperfections. Recommended steps:

Sand the sealing surface to bright metal
Clean the sealing area with water
Dry thoroughly
Mix the metal filled epoxy following manufacturer’s directions
Apply a thin bead on the sealing surface
Using a plastic implement smooth the bead covering damage and imperfections. Make sure the epoxy is smooth and even.
Let harden, install cap.

Note: This technique has been used on GM, VW and Porsche radiators to good effect.


Thermostat

The thermostat has two important jobs to perform; to accelerate engine warm-up and to regulate the engine's operating temperature. A quality thermostat ensures excellent fuel economy, reduces engine wear, diminishes emissions and blow-by, improves cold weather drivability, provides adequate heater output, and deters overheating. This is accomplished by blocking the circulation of coolant between the engine and radiator until the engine has reached its predetermined temperature. The thermostat then opens as required in response to changes in coolant temperature to keep the engine's temperature within the desired operating range.

Thermostats have a “rated” temperature such as 180º F or 195º F. This is the temperature the thermostat will start to open, give or take 3º.

Usually located within a metal or plastic housing where the upper radiator hose connects to the engine, most of today’s thermostats utilize the "reverse poppet" design, which opens against the flow of the coolant. Thermostats have a wax filled copper housing or cup called a "heat motor" that pushes the thermostat open against spring pressure.

As the engine's coolant warms up, the increase in heat causes the wax to melt and expand. The wax pushes against a piston inside a rubber boot. This forces the piston outward to open the thermostat. Within 3º or 4º F. of the thermostat preset/rated temperature which is usually marked on the thermostat, the thermostat begins to unseat so coolant can start to circulate between the engine and radiator. It continues to open until engine cooling requirements are satisfied. It is fully open about 15º-20º above its rated temperature. If the temperature of the circulating coolant begins to drop, the wax element contracts, allowing spring tension to close the thermostat, thus decreasing coolant flow through the radiator.

On some applications, the thermostat performs an additional function. It closes off a bypass circuit inside the engine when it opens the radiator circuit. The bypass circuit circulates coolant inside the engine so that hot spots can’t form when the radiator circuit is closed.

Many thermostats have a “jiggle pin” that allows trapped air in the cooling system to pass through the thermostat and be removed from the system. If a Stant thermostat does not have a jiggle pin, it will have a "bleed notch” or other method of removing air from the system.


Thermostat failures

There is no such thing as a thermostat that will fail in a “safe” position. All thermostats will fail in either a closed or open position. One brand claims it fails in a safe position, but it simply locks itself open when it is a full stroke open position. It will not spring open if it fails in a closed position.

A thermostat fails “open” if the return spring breaks or debris prevents the thermostat valve from fully seating or closing. In this instance the thermostat allows continuous coolant flow to the radiator; therefore, the engine will be overcooled. The tangible effects are poor warm up and heater performance, increased engine emissions and reduced fuel economy. For these reasons, an engine should never be operated without a thermostat in place, even in extreme temperatures.

A thermostat will fail “closed” if the wax element has been damaged by overheating (from loss of coolant, a defective electric cooling fan or fan clutch) or corrosion (from not changing the anti-freeze often enough). This failure prevents the flow of coolant to the radiator; therefore, the engine will be overheated. The tangible effects are a boil over, the inability to operate the vehicle, and the likelihood of severe engine damage. For these reasons alone, when an engine overheats, it’s a good idea to replace the thermostat whether it caused the problem or not.
[edit] Replacement thermostats

The temperature rating of a replacement thermostat must be the correct one for the application because of the adverse effects the wrong thermostat can have on drivability, engine performance and emissions.

The temperature rating specified by the car manufacturer is especially important in many 1981 and newer vehicles because the on-board computer monitors coolant temperature through a coolant sensor to control fuel enrichment, spark timing and operation of the EGR valve. Even on vehicles without computers, thermal vacuum switches that react to a specific coolant temperature are often used to open and close various vacuum circuits that regulate fuel enrichment, timing and EGR. If a colder thermostat is installed, the coolant may never get hot enough to trigger the appropriate control functions or to allow a computer system to go into “closed loop”. Too hot a thermostat can also interfere with the proper operation of engine controls, and increase the engine’s operating temperature to the point where it may experience detonation (spark knock).
[edit] Thermostat checks

One way to determine if the thermostat is doing its job is to feel the upper radiator hose after starting a cold engine. The hose should not feel hot until the engine has warmed up. If the hose starts to feel hot after only a couple of minutes, the thermostat may be stuck open or not closing completely. Once the engine is warm, the hose should feel hot as coolant circulates between the engine and radiator. If the hose does not feel hot, the thermostat may be stuck shut, blocking the flow of coolant.

A thermostat can be tested by suspending it, using a string through the valve, in a bucket of boiling 50/50 coolant and water. If the thermostat is working it will fall off the string as it starts to open after being in the hot/boiling coolant for a few minutes. When removed and allowed to cool, the thermostat should close.
[edit] Replacement tips

Don't overlook the water outlet covering the thermostat. Check for cracks, broken flanges, internal pitting and corrosion, and erosion at the hose neck (a real problem with most aluminum housings). The gasket surface must be flat and free from warping or deep scratches.
Scrape the mating surfaces on the thermostat housing and engine to remove all traces of old gasket material. Use care on aluminum because the soft metal can be easily scratched.
Temporarily stuffing a clean rag into the thermostat opening on the engine while the housing is removed helps keep debris out of the cooling system.
Install the new thermostat so the copper heat sensing element is toward the engine. If installed upside down, it won’t open.
Torque the thermostat housing bolts evenly and to the manufacturer's recommendations.
To insure air has been removed from the cooling system after replacing a thermostat, be sure to run the engine a few minutes, let it cool, and refill the antifreeze as needed.

NOTE: The old type of thermostat used metal bellows filled with a liquid. The condensed liquid would "suck" the bellows closed. This type of thermostat always fails in the open position which is extremely convenient as one does not have to buy a new cylinder head or engine. Nowadays this type is very difficult to obtain.

User avatar
black start
TriniTuner 24-7
Posts: 7974
Joined: February 25th, 2010, 10:42 am
Location: conquering the pothole solodex

Re: Keep cool! All about your cooling system.....

Postby black start » October 3rd, 2012, 10:52 pm

thank you good sir....

User avatar
lighthammer
punchin NOS
Posts: 4519
Joined: April 15th, 2010, 2:35 pm
Location: Somewhere over the rainbow...

Re: Keep cool! All about your cooling system.....

Postby lighthammer » October 4th, 2012, 6:36 am

Any mods here who can make this post a sticky?

User avatar
FilterProz
3NE 2NR for life
Posts: 187
Joined: March 14th, 2011, 10:25 am
Location: South
Contact:

Re: Keep cool! All about your cooling system.....

Postby FilterProz » October 4th, 2012, 9:46 pm

nice post I am bringing in some Genuine Nissan coolant like the one used in massey soon will keep you posted...

User avatar
neckto
I LUV THIS PLACE
Posts: 918
Joined: July 7th, 2003, 10:03 am
Location: DIY - ing
Contact:

Re: Keep cool! All about your cooling system.....

Postby neckto » October 5th, 2012, 8:42 am

nice info

User avatar
lighthammer
punchin NOS
Posts: 4519
Joined: April 15th, 2010, 2:35 pm
Location: Somewhere over the rainbow...

Re: Keep cool! All about your cooling system.....

Postby lighthammer » October 12th, 2012, 2:22 pm

Woo hoo!! Sticky!!

User avatar
Cooper
3NE2NR Diesel Boyz
Posts: 1516
Joined: July 28th, 2003, 7:47 am

Re: Keep cool! All about your cooling system.....

Postby Cooper » October 22nd, 2012, 9:50 am

Nice post LH.

One question... if I need to top up my coolant, is it okay to mix a different brand to what the stealership uses?

User avatar
lighthammer
punchin NOS
Posts: 4519
Joined: April 15th, 2010, 2:35 pm
Location: Somewhere over the rainbow...

Re: Keep cool! All about your cooling system.....

Postby lighthammer » October 22nd, 2012, 10:20 am

hmmm... maybe with the cheaper ones, that are pre-mixed.
I prefer to use back the same ones, or just might as well drain out all the coolant from the radiator and do a lil flush one time (run the hose through). Then refill with your favourite brand of coolant, top up, leave the cap off and run for a min or so to get rid of bubbles, et voila, you're good to go.

User avatar
Cooper
3NE2NR Diesel Boyz
Posts: 1516
Joined: July 28th, 2003, 7:47 am

Re: Keep cool! All about your cooling system.....

Postby Cooper » October 22nd, 2012, 10:51 am

I have a 1 gallon bottle of green Prestone coolant which I use to top up in the car but the standards don't match what is recommended by the stealership on the Motocraft website. Guess I'll match up the brand for the Ranger. I'm running a WLT engine....not gonna take any chances :-P

sablo77
Street 2NR
Posts: 60
Joined: March 7th, 2008, 2:34 pm
Contact:

Re: Keep cool! All about your cooling system.....

Postby sablo77 » December 18th, 2012, 8:47 am

i wonder where i can go to have my thermostat checked out. i live in martabella and work in couva so any where from south to central will work for me ....LT link me na

User avatar
lighthammer
punchin NOS
Posts: 4519
Joined: April 15th, 2010, 2:35 pm
Location: Somewhere over the rainbow...

Re: Keep cool! All about your cooling system.....

Postby lighthammer » December 19th, 2012, 1:58 am

Had a recent problem with my cooling system.

Symptoms are as follows:
- while driving south for recent off-road rally, engine temp suddenly and without previous warning started to climb, so much that the AC suddenly became warm (no previous indication of malfunction)
- stopped and cooled down, saw that radiator water level was low and coolant was brown-coloured and smelled "scorched" (didn't smell like new coolant)
- after cooling off, replaced old coolant with 50:50 mixture of NP Radol coolant concentration : water that I bought from a nearby NP Quickserv
- drove home, checked for leaks/broken hoses/radiator defects/water pump problems/Clutch fan oil leak or free-play when engine off - NO PROBLEMS AT ALL.


Over the next couple of weeks, the overheating problem remained.... but in a slightly unusual way:
- at idle and slow-driving/traffic crawling, engine temp stayed absolutely normal, and AC was cold throughout the whole time
- but when driving at highway speeds, engine temp would start to climb again once I reached over 3000 RPM, but would cool down after I backed off the throttle.
- Eventually took out the thermostat and checked it in a pot of boiling water, was opening and closing properly at operating temps.
- drove without the thermostat for a couple weeks, still had the overheating problem... temperature climbs at 3000RPM or 110km/h or more on highway... but not at lower speeds
- still no signs of leaks, water levels and coolant levels were good, changed out the NP Radol and used Prestone coolant, clutch fan was working properly (supposed to have mild resistance when engine hot and turned off, free-play when engine warm means the clutch fluid is worn and needs replacing)
- took off the radiator cap when engine was cold and switched on, revved the engine and got a good flow of water coming spewing out of the cap... meaning the water pump was working properly.
- scrapped down the radiator and did a flush through the top-cap - the water coming out from the bottom outlet was clean and clear, hence I could assume no deposits inside (plus it was a sealed system and I always used bottled water to top it up, to avoid mineral deposits cuz my local water table is quite hard/full of calcium).
- washed out the radiator and condenser fins.... LOTS of mud in there from my offroading adventures (took about an hour of washing and half a container of purple blaster to get the water to run clean!)


So... i couldn't figure out what was the problem... until I read the article above and something clicked...... I WAS USING THE WRONG COOLANT.

The NP Radol and Prestone coolants probably weren't rated for the operating temps for diesel, or at least it was out of the operating range for my Navara's YD25ddti - I dunno, maybe I had mixed them wrong, or I put them in on the wrong proportions. I thought to myself that maybe the coolant was meant for gasoline engines, and not so much for the hotter operating temps of a diesel.

So I immediately went down to the nearest Motorist shop (since it's a nissan) and got some Original, genuine Nissan coolant that was rated for my Navara's engine - paid $425 for a large container (approx 1 1/2 gallons, can't remember the exact size). Simply poured the entire contents of the large bottle into the rad and coolant bottle, was exactly enough for fulling the radiator and bottle to exact limits!! (guy at motorist said no need to mix, just pour straight in).

Also bought a new thermostat for the YD25DDti engine (might as well change it, the nav was running at 72,000km on the Odo anyway).


Result - no more overheating! I even ran the engine at 4200rpm for approx 5 mins (stayed in 5th gear and gunned it all the way to 110km/h), put the ac on full blast - and nothing happened. Needle stayed put like it was painted onto the dash.


So here were some of my conclusions:
- use proper rated coolant for the correct application. A trusted and well-competent mechanic friend of mine said that coolants do differ in quality and you get what you pay for. $45 for a gallon of Prestone vs. $450 for a couple gallons of Nissan original coolant will definitely make a difference (plus something about pre-mixing in exact proportions, surfactants, minerals etc in the original coolant that the Nissan engineers intended, that 3rd party coolants could never match esp for specific vehicles).
- make sure you clean your cooling system at least once a year. A radiator flush at a reputable radiator-garage will benefit you greatly, as well as checking your thermostat every 50,000 - 60,000km. Try to use original parts for thermostats.
- my navara has 4" of lift, meaning it's a lot taller than stock navara's, plus it runs 305/60R18 mud terrain tyres - hence the engine has a lot more work to do, a lot more wind-resistance on the highway, etc. This translates into higher loads on the engine esp at high speed... which probably is why it only overheated at load/high speed and not at idle. The engine was working too hard for the 3rd party coolant to keep up with.


So folks.... that's the moral of my story. Hope you enjoyed reading it and if anyone learned anything from my experience, then I'm happy.


Keep on Truckin'!

4g63
Street 2NR
Posts: 48
Joined: January 18th, 2004, 2:21 pm

Re: Keep cool! All about your cooling system.....

Postby 4g63 » December 19th, 2012, 10:45 am

did you check melvin's radiator repairs on union rd.?

4g63
Street 2NR
Posts: 48
Joined: January 18th, 2004, 2:21 pm

Re: Keep cool! All about your cooling system.....

Postby 4g63 » December 19th, 2012, 10:53 am

thanks for that info. there boy lighthammer. cheap coolant cud really get you in a wax.
lemme know if you want to go and toss the dura-torq bt-50 2.2

User avatar
sweeks
3NE2NR Diesel Boyz
Posts: 1988
Joined: April 12th, 2006, 7:53 pm
Location: Central
Contact:

Re: Keep cool! All about your cooling system.....

Postby sweeks » December 20th, 2012, 12:49 pm

Cooper wrote:Nice post LH.

One question... if I need to top up my coolant, is it okay to mix a different brand to what the stealership uses?


I've used distilled water to top up in the past. I personally wouldn't mix two brands of coolant since the chemical composition in both may vary significantly.

User avatar
PariaMan
punchin NOS
Posts: 3176
Joined: July 9th, 2010, 10:38 am

Re: Keep cool! All about your cooling system.....

Postby PariaMan » December 21st, 2012, 3:38 pm

"Toyota Genuine coolant is the only guaranteed compatible antifreeze for your vehicle's cooling system and offers protection against corrosion of metallic parts and damage to rubber parts. The use of non-genuine coolants will corrode the parts and gradually block the cooling system, damaging the engine. The boiling point of the Genuine coolant is kept at the optimum level for operating temperatures in a Toyota vehicle. This ensures no evaporation of the coolant, thereby maintaining the level of the coolant for optimum operating temperatures. Features include:

*Quality
'Designed, tested and approved by Toyota R&D.
'Ethylene Glycol based for extra long lasting aluminum protection.

'No silicates.
'Cannot gel.
'No seal abrasion.

'No borates.
'No aluminum corrosion or pitting.

'Formulated with de-ionized water
'Pre-Diluted 50/50
'No additional water needed for reducing concentration.
'Pink coolant - for use in models which require the Super Long Life coolant."


I will pay the extra for the long life. Also read where the said the long life is only long life if not mixed with normal coolant.

When you consider the problems that can arise seems to be worth it!

User avatar
sweeks
3NE2NR Diesel Boyz
Posts: 1988
Joined: April 12th, 2006, 7:53 pm
Location: Central
Contact:

Re: Keep cool! All about your cooling system.....

Postby sweeks » December 21st, 2012, 9:08 pm

Toyota Longlife Coolant is the best I've seen. I've advised ppl in the past not to change it under 100 000km, caused it's good up to 160 000km.

User avatar
lighthammer
punchin NOS
Posts: 4519
Joined: April 15th, 2010, 2:35 pm
Location: Somewhere over the rainbow...

Re: Keep cool! All about your cooling system.....

Postby lighthammer » December 22nd, 2012, 3:43 am

Well, I'd consider changing the coolant out a littler earlier if the truck undergoes high stress loads frequently, eg offroading or towing or hauling cargo.

But yeah, I believe in using original coolant..... Maybe in a gasoline engine I'd take a chance and try other coolant, but not in a high performance diesel engine.

User avatar
PariaMan
punchin NOS
Posts: 3176
Joined: July 9th, 2010, 10:38 am

Re: Keep cool! All about your cooling system.....

Postby PariaMan » December 24th, 2012, 11:06 am

lighthammer wrote:Well, I'd consider changing the coolant out a littler earlier if the truck undergoes high stress loads frequently, eg offroading or towing or hauling cargo.

But yeah, I believe in using original coolant..... Maybe in a gasoline engine I'd take a chance and try other coolant, but not in a high performance diesel engine.



Was surprised that a man like you got caught using non original coolant!

4g63
Street 2NR
Posts: 48
Joined: January 18th, 2004, 2:21 pm

Re: Keep cool! All about your cooling system.....

Postby 4g63 » December 25th, 2012, 3:14 am

any of you guys know the price for the toyota genuine coolant paria man mentioned? mention the quantity as well. can you get this outside of toyota or must you buy it at the firm?

User avatar
sweeks
3NE2NR Diesel Boyz
Posts: 1988
Joined: April 12th, 2006, 7:53 pm
Location: Central
Contact:

Re: Keep cool! All about your cooling system.....

Postby sweeks » December 25th, 2012, 7:02 am

I've seen it at Reputable Auto in Couva 636-0849

User avatar
PariaMan
punchin NOS
Posts: 3176
Joined: July 9th, 2010, 10:38 am

Re: Keep cool! All about your cooling system.....

Postby PariaMan » December 28th, 2012, 8:56 am

Got it at both dollar saver and El Socorro Auto think that dollar savers was cheaper. Both were cheaper than Toyota!

User avatar
droppa
punchin NOS
Posts: 4191
Joined: January 2nd, 2004, 9:20 am
Location: when in doubt, use 4Lo!!!!!!

Re: Keep cool! All about your cooling system.....

Postby droppa » December 28th, 2012, 10:33 am

removing the thermostat in these modern diesel engines is a bad bad idea, alot of owners dont know that under heating is just as bad as over heating....i learnt that the expensive way.....

and yeah genuine coolant all the way, or a good reputable brand!!!

i used chevron delo coolant concentrate, it has a mixing chart at the back to suit your temperature range, i mixxed mine for between 70-80degC, and with a new thermo installed and proper monitoring of the system, i had no problems...........

User avatar
1001
Sweet on this forum
Posts: 275
Joined: October 3rd, 2013, 9:32 pm

Re: Keep cool! All about your cooling system.....

Postby 1001 » November 22nd, 2013, 8:34 pm

good info :scatter:

User avatar
MadCrix
3NE 2NR Moderator
Posts: 3523
Joined: March 22nd, 2004, 2:46 pm
Location: Where your ride simply cannot go
Contact:

Re: Keep cool! All about your cooling system.....

Postby MadCrix » August 12th, 2014, 2:21 pm

I using Valvoline coolant in de b2500 and it working good no problems. rad had a lot of mud stuck in radiator fins.. still has I believe. hadda remove completely to get all out.. will do that sometime

Mr. Wheeler
Street 2NR
Posts: 49
Joined: January 24th, 2006, 1:43 pm

Re: Keep cool! All about your cooling system.....

Postby Mr. Wheeler » October 29th, 2014, 5:23 pm

D Hilux needle Started to Climb...
I knew it was about that Time...
To spend more than a dime...
Use Original Coolant and continue to lime!!

User avatar
*$kїđž!™
TriniTuner 24-7
Posts: 11109
Joined: December 25th, 2006, 2:58 pm
Location: VIP SECTION

Re: Keep cool! All about your cooling system.....

Postby *$kїđž!™ » June 2nd, 2015, 12:18 am

Guys what coolant does the hilux use...looking to top up......

Tridenture
Riding on 13's
Posts: 8
Joined: June 22nd, 2015, 4:24 pm

Re: Keep cool! All about your cooling system.....

Postby Tridenture » June 22nd, 2015, 4:29 pm

Good find & thanks! Bookmarking it.

WestIndian424
Riding on 17's
Posts: 1501
Joined: March 3rd, 2013, 1:07 pm

Re: Keep cool! All about your cooling system.....

Postby WestIndian424 » May 29th, 2018, 9:57 pm

Bumping an old thread...what is the best coolant for the 2008 Ranger/BT50 with a WL engine(base model)?

User avatar
*$kїđž!™
TriniTuner 24-7
Posts: 11109
Joined: December 25th, 2006, 2:58 pm
Location: VIP SECTION

Re: Keep cool! All about your cooling system.....

Postby *$kїđž!™ » May 30th, 2018, 8:22 pm

Original is the best way to go...visit the tune up shop u bound to find it there

User avatar
supernedd
Chronic TriniTuner
Posts: 655
Joined: April 14th, 2012, 8:44 pm

Re: Keep cool! All about your cooling system.....

Postby supernedd » October 3rd, 2018, 2:31 pm

Calor wrote:Bumping an old thread...what is the best coolant for the 2008 Ranger/BT50 with a WL engine(base model)?
did u find it n what is d correct radiator cap rating.. how many psi ..n where can i get an original thermostat

Advertisement

Return to “Trucks & Pickups”

Who is online

Users browsing this forum: No registered users and 5 guests