Forums

ddog

For anyone curious, the problem was the 12V feed to the coil positive. On the liberty harness the 12V feed for the coil comes from the ECCS relay. I have the switched 12V feed to the distributor and around 10V on crank which is normal. As the voltage checks out OK I assume it seems to be an amperage...

ddog

Anyone knows if the Avenir and VVL distributors are the same? I see they are both 8pin.

ddog

Quick thought just popped up, are the GA and SR internal coil and ignition module the same?

ddog

I did try 3 distributors in all, but as you said all used. While possible I would find it strange that they would all have the same problem and unfortunately I had no other vehicle to test them on. There are new plugs and relatively new plug wires from my GA16 engine that was known working. I did tr...

ddog

Hi folks, I recently installed an Avenir style SR20DET into my B14 and now having some issues getting it to start. The particular version of the engine is from the Nissan liberty. I am getting a very weak spark out of the distributor, too weak to start the engine. Initially I though it may have been...

ddog

I have a SR20DET from a liberty (PNM12) which I am looking to install into my B14. I wanted to mate this to a small spline LSD gearbox but currently encountering issues with the axles and the rear gearbox bracket. Gearbox in question: https://forums.trinituner.com/upload/data/50/IMG_20191222_121559....

ddog

I haven't seen one of those in a loooong time. Unfortunately I don't own one but what info are you looking for? You can also head over to mazda626.net forums for advice.

ddog

Cool, thanks for the info, will check it out.

ddog

I think I got a regular B14 kit when I bought it, the piston size was the same as the regular B14 so the kit worked but it didn't have the slide pin insert rubber. The caliper works properly, but it doesn't retract after hitting the brake pedal because the slide pins get stuck in the slide pin rubbe...

ddog

Can anyone tell me who regrinds cams locally? I know that Zigs machine shop does it but are there any other places?

ddog

Does anyone know where I can get a full rebuild kit for the Pulsar AD22VF calipers? I have a problem where one caliper only holds on half the rotor. You can actually see the caliper rocking to one side when you apply brakes. The slide pins are good and well lubricated with brake grease but it seems ...

ddog

I believe this was taken from a website called gens x i think... <p> SR20DE ECU Pinout Reference (Australia) Whilst all due care and diligence has been used by me in creating these ecu pinouts, which are based on information from a range of sourses, I expressly disclaim all and any liability to any ...

ddog

http://www.sr20forum.com/technical-info ... ide-3.html

OBD1 GA15, GA16, SR20 are all the same pinouts.

ddog

If I recall correctly that p11 setup should be about an inch shorter than the B14 setup. I don't know what the actual height may be after install. I am guessing you may be a little bit lower than stock.

ddog

I tried a couple regular axles but it still leaks when using "LSD" gear oil. If I use straight 90 body oil it barely leaks, but I am guessing it affects the LSD as the car runs like crap after about 30km, feels like its holding back with some major power loss. After 30km the engine revs bu...

ddog

Hey guys, I am running a G16 LSD gear box on my B14 but having some problems with the right sides axle. The right side axle cup I got with the box seems to be a little longer than it should be. It mounts up perfectly fine, however it seems that it is maybe about an half inch longer than it should be...

ddog

Most likely the tiens. I have the gold tiens on my 14 and It does make the car firmer through the corners however the ride is a bit rough for daily use. The height drop is around 2.5" front and 1.7 or 1.8" in the back. I believe the green tiens are a little higher. The B14 only has about 3...

ddog

I am not sure if I am using the fast program correctly but I keep getting 38342 as the seal part number. However there are variations to this number when searching for the part online. These show up as 38342N or 3832M online and they are completely different seals. I have had this issue in the past ...

ddog

Anyone know what the seal number/ part number is, or where i can get it? Unfortunately there is no number on the original seal I removed.

ddog

cool, already got an almera pedal

ddog

I heard that the serena front caliper can bolt up on a B14 spindle but the serena rotor needs to be re-drilled. Anybody done this before or have any info on it? I know that it is a double piston setup but I have no idea what the rotor size is. Can a rotor from another vehicle with the B14 bolt patte...

ddog

I found out that B15 clutch cylinder should work. Now I need a clutch pedal. I thought I had the correct pedal but the bolt up is completely different. Any idea which pedal is a direct fit? primera, B15?

ddog

Anyone know what clutch cylinder (firewall) works on the B14 and where I can get one? I heard primera does but I am not sure. I went to a couple parts places today but none of them even had clutch cylinders.

ddog

Any luck with this? I am in the same position with my coupe None so far. Initially planned to go with a FSDE or ZE conversion or maybe even a KL. Was trying to source a front cut to do the conversion but that didn't work out as planned. So I dusted off the cobwebs and started servicing the carb for...

ddog

Yeh man, I think I found it here viewtopic.php?f=21&t=104415&hilit=SR+gearbox The small spline box seems to be the SR18 LSD type that should work with my GA16 LSD axles. The only downfall is the small spline is cable type and not hydraulic. What I didn't get is what type of axles are needed ...

ddog

Hey Guys, I was originally planning to swap in an Avenir SR20 DET into my B14 but given the current price and rarity of the engines ($9000 +), I am planning to swap my GA16DE with a P11 SR20 VVL type engine instead. I am aware that some sort of management/ controller would be needed to engage the VV...

ddog

http://forum.pulsar.org.au/showthread.p ... post859245 The above link is build thread for a SR20DET Auto pulsar. End result was the tranny and torque convertor had to be modified for it to shift gears properly. They used a SR18 LSD transmission however. I was considering this some time back but it w...

ddog

Most shops are selling the exhaust bends for around the same price 290 - 300 for the steel bends. Unfortunately J force does not sell the bends. Now I am actually looking for bends to build a cold air intake setup, a 45 and 90 degree bend. Would rather it be made out of aluminum. I have been able to...

ddog

This should be a simple procedure. You may need to use an impact screwdriver to remove the "phillips" screws holding it down as some times it is very difficult to break them free with a regular screwdriver. You generally don't need to silicone the entire area, just where the cam "hump...

ddog

Thanks for the response, you won't believe how much parts place tell me to put an SR in it LOL! Anyway it's a GC coupe and I am looking to go fuel injected in it. The above engines are choices that I had in mind for it. Not looking to go hybrid, want to keep it mazda. We use to have a modified MX6 f...