trinituner.com

hey ppl im havin some problems with my 3rd ge.When the car is cold it starts normal and drives .there is a slight misfiring that takes place.
if i switch off the car doesnt start.but if i try to push start it it starts nromal.
also if i spray some bars in the intake while its hot it starts normal.im located in trincity area.can some1 advise me where to go to get this servied and/or also has info on what the problem might me.its the 13b twin turbo btw

you can check sean reddy in orange grove road.he does great work, but is a bit pricey.

sounding like the primary injectors are leaking down, or the coils are faulty.

The coils when they get hot stop working or start shorting, remember they are located directly over the engine. That's why the car starts to misfire when you start to drive. Could also be TPS, also when it gets hot stops working properly.

If the injectors are leaking down, you would get the starting problem but not the misfiring, so I am leaning towards coils.

The bars would increase the compression by forming a better seal and it would start like if you push start. (compression would ignite the air/fuel mixture easily) like how ppl put oil down a carb to start.

Well the rotary mechanic part, I can't give any advice there, we don't trust any, just use your discretion and go by somebody you think you can trust.

try sean he is ok....but do your research after dat......pm me when u ready......don't check any in the arima area...trust me!

is it possible its the seal problem and the engine has to rebuild.what other symtoms would i get if the engine needed a rebuild?

if you in trincity, go by weevee 484-7210 (dinsley road / joe street). he is very honest and will get the job done right.

yeah u better go by weevee....

BAD>>>>> http://www.youtube.com/watch?v=gn40QqKg ... re=related


GOOD>>>http://www.youtube.com/watch?v=cGiNvwMPoXc

is there a rotary mechanic named gilmore???

yeah.....forget him

rxforever wrote:yeah.....forget him

Whats wrong with gilmore?....I'm about to do business with him...to repair a 2nd gen of mine...so any referrals about him would be nice..

How about Anil from up trincity side? Any reviews on him?

is this something u guys can use?

RX-7 FD3S 13B 93-99 Turbo Exhaust Manifold
Fits T04R / T78 / T88 / TD07 / TD08 with T4 Flange
Fits HKS Wastegate Flange

Porn Star wrote:How about Anil from up trincity side? Any reviews on him?

used to go by him early on...he does know a lot about rx7s especially 3rdgens and he does neat work (as far as i had seen)...ppl say both good and bad things about him, im sure like all other business ppl...i stopped going by him though...not because of what i heard ppl say but because of personal experiences...if u try him out probably your experience might b better than mine

i want a bonnet like urs in ur pics..ImamurA

rebuilt my engine by stephen, no problems......

looking for a mechanic to do other things like change bushings, master cylinder rubbers etc.....anyone can recommend someone from south???

rxforever wrote:i want a bonnet like urs in ur pics..ImamurA

lol thanks man

toyoman wrote:rebuilt my engine by stephen, no problems......

looking for a mechanic to do other things like change bushings, master cylinder rubbers etc.....anyone can recommend someone from south???

check suraj 3369020 from penal/barrackpore side

cool thanks....

since this seems to be the place to ask
who can complete a series 7 swap into a 2ndgen?
have the engine installed need it to be wired and driveshaft cut and little final touches

Sounds like the engine is being flooded.

Check Sean or Anil .. just let them diagnose the problem and agree to a repair price BEFORE they do anything.. you can go by anyone as long as you set the ground rules FIRST

How much would it cost to rebuild a 3rd gen 13b engine with labour??

there are varying prices, numerous types of seals available, depends alot on the rebuild, if apex seals were damaged, u may need new rotors and rotor housing, hving a $15 000 on stand by is a good idea! however ur best bet is to try to avoid a rebuild in the first place, learn more about ur car, find out y they fail and deal with cooling issues.......